Export limit exceeded: 25096 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (25096 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2023-54037 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: ice: prevent NULL pointer deref during reload Calling ethtool during reload can lead to call trace, because VSI isn't configured for some time, but netdev is alive. To fix it add rtnl lock for VSI deconfig and config. Set ::num_q_vectors to 0 after freeing and add a check for ::tx/rx_rings in ring related ethtool ops. Add proper unroll of filters in ice_start_eth(). Reproduction: $watch -n 0.1 -d 'ethtool -g enp24s0f0np0' $devlink dev reload pci/0000:18:00.0 action driver_reinit Call trace before fix: [66303.926205] BUG: kernel NULL pointer dereference, address: 0000000000000000 [66303.926259] #PF: supervisor read access in kernel mode [66303.926286] #PF: error_code(0x0000) - not-present page [66303.926311] PGD 0 P4D 0 [66303.926332] Oops: 0000 [#1] PREEMPT SMP PTI [66303.926358] CPU: 4 PID: 933821 Comm: ethtool Kdump: loaded Tainted: G OE 6.4.0-rc5+ #1 [66303.926400] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.00.01.0014.070920180847 07/09/2018 [66303.926446] RIP: 0010:ice_get_ringparam+0x22/0x50 [ice] [66303.926649] Code: 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 48 8b 87 c0 09 00 00 c7 46 04 e0 1f 00 00 c7 46 10 e0 1f 00 00 48 8b 50 20 <48> 8b 12 0f b7 52 3a 89 56 14 48 8b 40 28 48 8b 00 0f b7 40 58 48 [66303.926722] RSP: 0018:ffffad40472f39c8 EFLAGS: 00010246 [66303.926749] RAX: ffff98a8ada05828 RBX: ffff98a8c46dd060 RCX: ffffad40472f3b48 [66303.926781] RDX: 0000000000000000 RSI: ffff98a8c46dd068 RDI: ffff98a8b23c4000 [66303.926811] RBP: ffffad40472f3b48 R08: 00000000000337b0 R09: 0000000000000000 [66303.926843] R10: 0000000000000001 R11: 0000000000000100 R12: ffff98a8b23c4000 [66303.926874] R13: ffff98a8c46dd060 R14: 000000000000000f R15: ffffad40472f3a50 [66303.926906] FS: 00007f6397966740(0000) GS:ffff98b390900000(0000) knlGS:0000000000000000 [66303.926941] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [66303.926967] CR2: 0000000000000000 CR3: 000000011ac20002 CR4: 00000000007706e0 [66303.926999] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [66303.927029] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [66303.927060] PKRU: 55555554 [66303.927075] Call Trace: [66303.927094] <TASK> [66303.927111] ? __die+0x23/0x70 [66303.927140] ? page_fault_oops+0x171/0x4e0 [66303.927176] ? exc_page_fault+0x7f/0x180 [66303.927209] ? asm_exc_page_fault+0x26/0x30 [66303.927244] ? ice_get_ringparam+0x22/0x50 [ice] [66303.927433] rings_prepare_data+0x62/0x80 [66303.927469] ethnl_default_doit+0xe2/0x350 [66303.927501] genl_family_rcv_msg_doit.isra.0+0xe3/0x140 [66303.927538] genl_rcv_msg+0x1b1/0x2c0 [66303.927561] ? __pfx_ethnl_default_doit+0x10/0x10 [66303.927590] ? __pfx_genl_rcv_msg+0x10/0x10 [66303.927615] netlink_rcv_skb+0x58/0x110 [66303.927644] genl_rcv+0x28/0x40 [66303.927665] netlink_unicast+0x19e/0x290 [66303.927691] netlink_sendmsg+0x254/0x4d0 [66303.927717] sock_sendmsg+0x93/0xa0 [66303.927743] __sys_sendto+0x126/0x170 [66303.927780] __x64_sys_sendto+0x24/0x30 [66303.928593] do_syscall_64+0x5d/0x90 [66303.929370] ? __count_memcg_events+0x60/0xa0 [66303.930146] ? count_memcg_events.constprop.0+0x1a/0x30 [66303.930920] ? handle_mm_fault+0x9e/0x350 [66303.931688] ? do_user_addr_fault+0x258/0x740 [66303.932452] ? exc_page_fault+0x7f/0x180 [66303.933193] entry_SYSCALL_64_after_hwframe+0x72/0xdc | ||||
| CVE-2023-54032 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race when deleting quota root from the dirty cow roots list When disabling quotas we are deleting the quota root from the list fs_info->dirty_cowonly_roots without taking the lock that protects it, which is struct btrfs_fs_info::trans_lock. This unsynchronized list manipulation may cause chaos if there's another concurrent manipulation of this list, such as when adding a root to it with ctree.c:add_root_to_dirty_list(). This can result in all sorts of weird failures caused by a race, such as the following crash: [337571.278245] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] PREEMPT SMP PTI [337571.278933] CPU: 1 PID: 115447 Comm: btrfs Tainted: G W 6.4.0-rc6-btrfs-next-134+ #1 [337571.279153] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [337571.279572] RIP: 0010:commit_cowonly_roots+0x11f/0x250 [btrfs] [337571.279928] Code: 85 38 06 00 (...) [337571.280363] RSP: 0018:ffff9f63446efba0 EFLAGS: 00010206 [337571.280582] RAX: ffff942d98ec2638 RBX: ffff9430b82b4c30 RCX: 0000000449e1c000 [337571.280798] RDX: dead000000000100 RSI: ffff9430021e4900 RDI: 0000000000036070 [337571.281015] RBP: ffff942d98ec2000 R08: ffff942d98ec2000 R09: 000000000000015b [337571.281254] R10: 0000000000000009 R11: 0000000000000001 R12: ffff942fe8fbf600 [337571.281476] R13: ffff942dabe23040 R14: ffff942dabe20800 R15: ffff942d92cf3b48 [337571.281723] FS: 00007f478adb7340(0000) GS:ffff94349fa40000(0000) knlGS:0000000000000000 [337571.281950] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [337571.282184] CR2: 00007f478ab9a3d5 CR3: 000000001e02c001 CR4: 0000000000370ee0 [337571.282416] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [337571.282647] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [337571.282874] Call Trace: [337571.283101] <TASK> [337571.283327] ? __die_body+0x1b/0x60 [337571.283570] ? die_addr+0x39/0x60 [337571.283796] ? exc_general_protection+0x22e/0x430 [337571.284022] ? asm_exc_general_protection+0x22/0x30 [337571.284251] ? commit_cowonly_roots+0x11f/0x250 [btrfs] [337571.284531] btrfs_commit_transaction+0x42e/0xf90 [btrfs] [337571.284803] ? _raw_spin_unlock+0x15/0x30 [337571.285031] ? release_extent_buffer+0x103/0x130 [btrfs] [337571.285305] reset_balance_state+0x152/0x1b0 [btrfs] [337571.285578] btrfs_balance+0xa50/0x11e0 [btrfs] [337571.285864] ? __kmem_cache_alloc_node+0x14a/0x410 [337571.286086] btrfs_ioctl+0x249a/0x3320 [btrfs] [337571.286358] ? mod_objcg_state+0xd2/0x360 [337571.286577] ? refill_obj_stock+0xb0/0x160 [337571.286798] ? seq_release+0x25/0x30 [337571.287016] ? __rseq_handle_notify_resume+0x3ba/0x4b0 [337571.287235] ? percpu_counter_add_batch+0x2e/0xa0 [337571.287455] ? __x64_sys_ioctl+0x88/0xc0 [337571.287675] __x64_sys_ioctl+0x88/0xc0 [337571.287901] do_syscall_64+0x38/0x90 [337571.288126] entry_SYSCALL_64_after_hwframe+0x72/0xdc [337571.288352] RIP: 0033:0x7f478aaffe9b So fix this by locking struct btrfs_fs_info::trans_lock before deleting the quota root from that list. | ||||
| CVE-2025-71064 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net: hns3: using the num_tqps in the vf driver to apply for resources Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller than hdev->num_tqps, which causes some hdev->htqp[i] to remain uninitialized in hclgevf_knic_setup(). Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps, ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent and that all elements are properly initialized. | ||||
| CVE-2025-68742 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Fix invalid prog->stats access when update_effective_progs fails Syzkaller triggers an invalid memory access issue following fault injection in update_effective_progs. The issue can be described as follows: __cgroup_bpf_detach update_effective_progs compute_effective_progs bpf_prog_array_alloc <-- fault inject purge_effective_progs /* change to dummy_bpf_prog */ array->items[index] = &dummy_bpf_prog.prog ---softirq start--- __do_softirq ... __cgroup_bpf_run_filter_skb __bpf_prog_run_save_cb bpf_prog_run stats = this_cpu_ptr(prog->stats) /* invalid memory access */ flags = u64_stats_update_begin_irqsave(&stats->syncp) ---softirq end--- static_branch_dec(&cgroup_bpf_enabled_key[atype]) The reason is that fault injection caused update_effective_progs to fail and then changed the original prog into dummy_bpf_prog.prog in purge_effective_progs. Then a softirq came, and accessing the members of dummy_bpf_prog.prog in the softirq triggers invalid mem access. To fix it, skip updating stats when stats is NULL. | ||||
| CVE-2025-71065 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock As Jiaming Zhang and syzbot reported, there is potential deadlock in f2fs as below: Chain exists of: &sbi->cp_rwsem --> fs_reclaim --> sb_internal#2 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(sb_internal#2); lock(fs_reclaim); lock(sb_internal#2); rlock(&sbi->cp_rwsem); *** DEADLOCK *** 3 locks held by kswapd0/73: #0: ffffffff8e247a40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat mm/vmscan.c:7015 [inline] #0: ffffffff8e247a40 (fs_reclaim){+.+.}-{0:0}, at: kswapd+0x951/0x2800 mm/vmscan.c:7389 #1: ffff8880118400e0 (&type->s_umount_key#50){.+.+}-{4:4}, at: super_trylock_shared fs/super.c:562 [inline] #1: ffff8880118400e0 (&type->s_umount_key#50){.+.+}-{4:4}, at: super_cache_scan+0x91/0x4b0 fs/super.c:197 #2: ffff888011840610 (sb_internal#2){.+.+}-{0:0}, at: f2fs_evict_inode+0x8d9/0x1b60 fs/f2fs/inode.c:890 stack backtrace: CPU: 0 UID: 0 PID: 73 Comm: kswapd0 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120 print_circular_bug+0x2ee/0x310 kernel/locking/lockdep.c:2043 check_noncircular+0x134/0x160 kernel/locking/lockdep.c:2175 check_prev_add kernel/locking/lockdep.c:3165 [inline] check_prevs_add kernel/locking/lockdep.c:3284 [inline] validate_chain+0xb9b/0x2140 kernel/locking/lockdep.c:3908 __lock_acquire+0xab9/0xd20 kernel/locking/lockdep.c:5237 lock_acquire+0x120/0x360 kernel/locking/lockdep.c:5868 down_read+0x46/0x2e0 kernel/locking/rwsem.c:1537 f2fs_down_read fs/f2fs/f2fs.h:2278 [inline] f2fs_lock_op fs/f2fs/f2fs.h:2357 [inline] f2fs_do_truncate_blocks+0x21c/0x10c0 fs/f2fs/file.c:791 f2fs_truncate_blocks+0x10a/0x300 fs/f2fs/file.c:867 f2fs_truncate+0x489/0x7c0 fs/f2fs/file.c:925 f2fs_evict_inode+0x9f2/0x1b60 fs/f2fs/inode.c:897 evict+0x504/0x9c0 fs/inode.c:810 f2fs_evict_inode+0x1dc/0x1b60 fs/f2fs/inode.c:853 evict+0x504/0x9c0 fs/inode.c:810 dispose_list fs/inode.c:852 [inline] prune_icache_sb+0x21b/0x2c0 fs/inode.c:1000 super_cache_scan+0x39b/0x4b0 fs/super.c:224 do_shrink_slab+0x6ef/0x1110 mm/shrinker.c:437 shrink_slab_memcg mm/shrinker.c:550 [inline] shrink_slab+0x7ef/0x10d0 mm/shrinker.c:628 shrink_one+0x28a/0x7c0 mm/vmscan.c:4955 shrink_many mm/vmscan.c:5016 [inline] lru_gen_shrink_node mm/vmscan.c:5094 [inline] shrink_node+0x315d/0x3780 mm/vmscan.c:6081 kswapd_shrink_node mm/vmscan.c:6941 [inline] balance_pgdat mm/vmscan.c:7124 [inline] kswapd+0x147c/0x2800 mm/vmscan.c:7389 kthread+0x70e/0x8a0 kernel/kthread.c:463 ret_from_fork+0x4bc/0x870 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> The root cause is deadlock among four locks as below: kswapd - fs_reclaim --- Lock A - shrink_one - evict - f2fs_evict_inode - sb_start_intwrite --- Lock B - iput - evict - f2fs_evict_inode - sb_start_intwrite --- Lock B - f2fs_truncate - f2fs_truncate_blocks - f2fs_do_truncate_blocks - f2fs_lock_op --- Lock C ioctl - f2fs_ioc_commit_atomic_write - f2fs_lock_op --- Lock C - __f2fs_commit_atomic_write - __replace_atomic_write_block - f2fs_get_dnode_of_data - __get_node_folio - f2fs_check_nid_range - f2fs_handle_error - f2fs_record_errors - f2fs_down_write --- Lock D open - do_open - do_truncate - security_inode_need_killpriv - f2fs_getxattr - lookup_all_xattrs - f2fs_handle_error - f2fs_record_errors - f2fs_down_write --- Lock D - f2fs_commit_super - read_mapping_folio - filemap_alloc_folio_noprof - prepare_alloc_pages - fs_reclaim_acquire --- Lock A In order to a ---truncated--- | ||||
| CVE-2025-71067 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ntfs: set dummy blocksize to read boot_block when mounting When mounting, sb->s_blocksize is used to read the boot_block without being defined or validated. Set a dummy blocksize before attempting to read the boot_block. The issue can be triggered with the following syz reproducer: mkdirat(0xffffffffffffff9c, &(0x7f0000000080)='./file1\x00', 0x0) r4 = openat$nullb(0xffffffffffffff9c, &(0x7f0000000040), 0x121403, 0x0) ioctl$FS_IOC_SETFLAGS(r4, 0x40081271, &(0x7f0000000980)=0x4000) mount(&(0x7f0000000140)=@nullb, &(0x7f0000000040)='./cgroup\x00', &(0x7f0000000000)='ntfs3\x00', 0x2208004, 0x0) syz_clone(0x88200200, 0x0, 0x0, 0x0, 0x0, 0x0) Here, the ioctl sets the bdev block size to 16384. During mount, get_tree_bdev_flags() calls sb_set_blocksize(sb, block_size(bdev)), but since block_size(bdev) > PAGE_SIZE, sb_set_blocksize() leaves sb->s_blocksize at zero. Later, ntfs_init_from_boot() attempts to read the boot_block while sb->s_blocksize is still zero, which triggers the bug. [almaz.alexandrovich@paragon-software.com: changed comment style, added return value handling] | ||||
| CVE-2025-71069 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: f2fs: invalidate dentry cache on failed whiteout creation F2FS can mount filesystems with corrupted directory depth values that get runtime-clamped to MAX_DIR_HASH_DEPTH. When RENAME_WHITEOUT operations are performed on such directories, f2fs_rename performs directory modifications (updating target entry and deleting source entry) before attempting to add the whiteout entry via f2fs_add_link. If f2fs_add_link fails due to the corrupted directory structure, the function returns an error to VFS, but the partial directory modifications have already been committed to disk. VFS assumes the entire rename operation failed and does not update the dentry cache, leaving stale mappings. In the error path, VFS does not call d_move() to update the dentry cache. This results in new_dentry still pointing to the old inode (new_inode) which has already had its i_nlink decremented to zero. The stale cache causes subsequent operations to incorrectly reference the freed inode. This causes subsequent operations to use cached dentry information that no longer matches the on-disk state. When a second rename targets the same entry, VFS attempts to decrement i_nlink on the stale inode, which may already have i_nlink=0, triggering a WARNING in drop_nlink(). Example sequence: 1. First rename (RENAME_WHITEOUT): file2 → file1 - f2fs updates file1 entry on disk (points to inode 8) - f2fs deletes file2 entry on disk - f2fs_add_link(whiteout) fails (corrupted directory) - Returns error to VFS - VFS does not call d_move() due to error - VFS cache still has: file1 → inode 7 (stale!) - inode 7 has i_nlink=0 (already decremented) 2. Second rename: file3 → file1 - VFS uses stale cache: file1 → inode 7 - Tries to drop_nlink on inode 7 (i_nlink already 0) - WARNING in drop_nlink() Fix this by explicitly invalidating old_dentry and new_dentry when f2fs_add_link fails during whiteout creation. This forces VFS to refresh from disk on subsequent operations, ensuring cache consistency even when the rename partially succeeds. Reproducer: 1. Mount F2FS image with corrupted i_current_depth 2. renameat2(file2, file1, RENAME_WHITEOUT) 3. renameat2(file3, file1, 0) 4. System triggers WARNING in drop_nlink() | ||||
| CVE-2025-68743 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: mshv: Fix create memory region overlap check The current check is incorrect; it only checks if the beginning or end of a region is within an existing region. This doesn't account for userspace specifying a region that begins before and ends after an existing region. Change the logic to a range intersection check against gfns and uaddrs for each region. Remove mshv_partition_region_by_uaddr() as it is no longer used. | ||||
| CVE-2025-7647 | 2 Linux, Run-llama | 2 Linux, Llama Index | 2026-04-15 | N/A |
| The llama-index-core package, up to version 0.12.44, contains a vulnerability in the `get_cache_dir()` function where a predictable, hardcoded directory path `/tmp/llama_index` is used on Linux systems without proper security controls. This vulnerability allows attackers on multi-user systems to steal proprietary models, poison cached embeddings, or conduct symlink attacks. The issue affects all Linux deployments where multiple users share the same system. The vulnerability is classified under CWE-379, CWE-377, and CWE-367, indicating insecure temporary file creation and potential race conditions. | ||||
| CVE-2023-54049 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: rpmsg: glink: Add check for kstrdup Add check for the return value of kstrdup() and return the error if it fails in order to avoid NULL pointer dereference. | ||||
| CVE-2023-54051 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: do not allow gso_size to be set to GSO_BY_FRAGS One missing check in virtio_net_hdr_to_skb() allowed syzbot to crash kernels again [1] Do not allow gso_size to be set to GSO_BY_FRAGS (0xffff), because this magic value is used by the kernel. [1] general protection fault, probably for non-canonical address 0xdffffc000000000e: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077] CPU: 0 PID: 5039 Comm: syz-executor401 Not tainted 6.5.0-rc5-next-20230809-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/26/2023 RIP: 0010:skb_segment+0x1a52/0x3ef0 net/core/skbuff.c:4500 Code: 00 00 00 e9 ab eb ff ff e8 6b 96 5d f9 48 8b 84 24 00 01 00 00 48 8d 78 70 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e ea 21 00 00 48 8b 84 24 00 01 RSP: 0018:ffffc90003d3f1c8 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 000000000001fffe RCX: 0000000000000000 RDX: 000000000000000e RSI: ffffffff882a3115 RDI: 0000000000000070 RBP: ffffc90003d3f378 R08: 0000000000000005 R09: 000000000000ffff R10: 000000000000ffff R11: 5ee4a93e456187d6 R12: 000000000001ffc6 R13: dffffc0000000000 R14: 0000000000000008 R15: 000000000000ffff FS: 00005555563f2380(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020020000 CR3: 000000001626d000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> udp6_ufo_fragment+0x9d2/0xd50 net/ipv6/udp_offload.c:109 ipv6_gso_segment+0x5c4/0x17b0 net/ipv6/ip6_offload.c:120 skb_mac_gso_segment+0x292/0x610 net/core/gso.c:53 __skb_gso_segment+0x339/0x710 net/core/gso.c:124 skb_gso_segment include/net/gso.h:83 [inline] validate_xmit_skb+0x3a5/0xf10 net/core/dev.c:3625 __dev_queue_xmit+0x8f0/0x3d60 net/core/dev.c:4329 dev_queue_xmit include/linux/netdevice.h:3082 [inline] packet_xmit+0x257/0x380 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3087 [inline] packet_sendmsg+0x24c7/0x5570 net/packet/af_packet.c:3119 sock_sendmsg_nosec net/socket.c:727 [inline] sock_sendmsg+0xd9/0x180 net/socket.c:750 ____sys_sendmsg+0x6ac/0x940 net/socket.c:2496 ___sys_sendmsg+0x135/0x1d0 net/socket.c:2550 __sys_sendmsg+0x117/0x1e0 net/socket.c:2579 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7ff27cdb34d9 | ||||
| CVE-2023-54070 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: igb: clean up in all error paths when enabling SR-IOV After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing the igb module could hang or crash (depending on the machine) when the module has been loaded with the max_vfs parameter set to some value != 0. In case of one test machine with a dual port 82580, this hang occurred: [ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1 [ 233.093257] igb 0000:41:00.1: IOV Disabled [ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0 [ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata) [ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000 [ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First) [ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c [ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata) [ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000 [ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First) [ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c [ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback) [ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0 [ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed [ 234.157244] igb 0000:41:00.0: IOV Disabled [ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds. [ 371.627489] Not tainted 6.4.0-dirty #2 [ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this. [ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0 [ 371.650330] Call Trace: [ 371.653061] <TASK> [ 371.655407] __schedule+0x20e/0x660 [ 371.659313] schedule+0x5a/0xd0 [ 371.662824] schedule_preempt_disabled+0x11/0x20 [ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0 [ 371.673237] ? __pfx_aer_root_reset+0x10/0x10 [ 371.678105] report_error_detected+0x25/0x1c0 [ 371.682974] ? __pfx_report_normal_detected+0x10/0x10 [ 371.688618] pci_walk_bus+0x72/0x90 [ 371.692519] pcie_do_recovery+0xb2/0x330 [ 371.696899] aer_process_err_devices+0x117/0x170 [ 371.702055] aer_isr+0x1c0/0x1e0 [ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0 [ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10 [ 371.715496] irq_thread_fn+0x20/0x60 [ 371.719491] irq_thread+0xe6/0x1b0 [ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10 [ 371.728255] ? __pfx_irq_thread+0x10/0x10 [ 371.732731] kthread+0xe2/0x110 [ 371.736243] ? __pfx_kthread+0x10/0x10 [ 371.740430] ret_from_fork+0x2c/0x50 [ 371.744428] </TASK> The reproducer was a simple script: #!/bin/sh for i in `seq 1 5`; do modprobe -rv igb modprobe -v igb max_vfs=1 sleep 1 modprobe -rv igb done It turned out that this could only be reproduce on 82580 (quad and dual-port), but not on 82576, i350 and i210. Further debugging showed that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because dev->is_physfn is 0 on 82580. Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), igb_enable_sriov() jumped into the "err_out" cleanup branch. After this commit it only returned the error code. So the cleanup didn't take place, and the incorrect VF setup in the igb_adapter structure fooled the igb driver into assuming that VFs have been set up where no VF actually existed. Fix this problem by cleaning up again if pci_enable_sriov() fails. | ||||
| CVE-2023-54080 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: skip splitting and logical rewriting on pre-alloc write When doing a relocation, there is a chance that at the time of btrfs_reloc_clone_csums(), there is no checksum for the corresponding region. In this case, btrfs_finish_ordered_zoned()'s sum points to an invalid item and so ordered_extent's logical is set to some invalid value. Then, btrfs_lookup_block_group() in btrfs_zone_finish_endio() failed to find a block group and will hit an assert or a null pointer dereference as following. This can be reprodcued by running btrfs/028 several times (e.g, 4 to 16 times) with a null_blk setup. The device's zone size and capacity is set to 32 MB and the storage size is set to 5 GB on my setup. KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f] CPU: 6 PID: 3105720 Comm: kworker/u16:13 Tainted: G W 6.5.0-rc6-kts+ #1 Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015 Workqueue: btrfs-endio-write btrfs_work_helper [btrfs] RIP: 0010:btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs] Code: 41 54 49 89 fc 55 48 89 f5 53 e8 57 7d fc ff 48 8d b8 88 00 00 00 48 89 c3 48 b8 00 00 00 00 00 > 3c 02 00 0f 85 02 01 00 00 f6 83 88 00 00 00 01 0f 84 a8 00 00 RSP: 0018:ffff88833cf87b08 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000011 RSI: 0000000000000004 RDI: 0000000000000088 RBP: 0000000000000002 R08: 0000000000000001 R09: ffffed102877b827 R10: ffff888143bdc13b R11: ffff888125b1cbc0 R12: ffff888143bdc000 R13: 0000000000007000 R14: ffff888125b1cba8 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88881e500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f3ed85223d5 CR3: 00000001519b4005 CR4: 00000000001706e0 Call Trace: <TASK> ? die_addr+0x3c/0xa0 ? exc_general_protection+0x148/0x220 ? asm_exc_general_protection+0x22/0x30 ? btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs] ? btrfs_zone_finish_endio.part.0+0x19/0x160 [btrfs] btrfs_finish_one_ordered+0x7b8/0x1de0 [btrfs] ? rcu_is_watching+0x11/0xb0 ? lock_release+0x47a/0x620 ? btrfs_finish_ordered_zoned+0x59b/0x800 [btrfs] ? __pfx_btrfs_finish_one_ordered+0x10/0x10 [btrfs] ? btrfs_finish_ordered_zoned+0x358/0x800 [btrfs] ? __smp_call_single_queue+0x124/0x350 ? rcu_is_watching+0x11/0xb0 btrfs_work_helper+0x19f/0xc60 [btrfs] ? __pfx_try_to_wake_up+0x10/0x10 ? _raw_spin_unlock_irq+0x24/0x50 ? rcu_is_watching+0x11/0xb0 process_one_work+0x8c1/0x1430 ? __pfx_lock_acquire+0x10/0x10 ? __pfx_process_one_work+0x10/0x10 ? __pfx_do_raw_spin_lock+0x10/0x10 ? _raw_spin_lock_irq+0x52/0x60 worker_thread+0x100/0x12c0 ? __kthread_parkme+0xc1/0x1f0 ? __pfx_worker_thread+0x10/0x10 kthread+0x2ea/0x3c0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> On the zoned mode, writing to pre-allocated region means data relocation write. Such write always uses WRITE command so there is no need of splitting and rewriting logical address. Thus, we can just skip the function for the case. | ||||
| CVE-2023-54078 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: media: max9286: Free control handler The control handler is leaked in some probe-time error paths, as well as in the remove path. Fix it. | ||||
| CVE-2025-68751 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: s390/fpu: Fix false-positive kmsan report in fpu_vstl() A false-positive kmsan report is detected when running ping command. An inline assembly instruction 'vstl' can write varied amount of bytes depending on value of 'index' argument. If 'index' > 0, 'vstl' writes at least 2 bytes. clang generates kmsan write helper call depending on inline assembly constraints. Constraints are evaluated compile-time, but value of 'index' argument is known only at runtime. clang currently generates call to __msan_instrument_asm_store with 1 byte as size. Manually call kmsan function to indicate correct amount of bytes written and fix false-positive report. This change fixes following kmsan reports: [ 36.563119] ===================================================== [ 36.563594] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70 [ 36.563852] virtqueue_add+0x35c6/0x7c70 [ 36.564016] virtqueue_add_outbuf+0xa0/0xb0 [ 36.564266] start_xmit+0x288c/0x4a20 [ 36.564460] dev_hard_start_xmit+0x302/0x900 [ 36.564649] sch_direct_xmit+0x340/0xea0 [ 36.564894] __dev_queue_xmit+0x2e94/0x59b0 [ 36.565058] neigh_resolve_output+0x936/0xb40 [ 36.565278] __neigh_update+0x2f66/0x3a60 [ 36.565499] neigh_update+0x52/0x60 [ 36.565683] arp_process+0x1588/0x2de0 [ 36.565916] NF_HOOK+0x1da/0x240 [ 36.566087] arp_rcv+0x3e4/0x6e0 [ 36.566306] __netif_receive_skb_list_core+0x1374/0x15a0 [ 36.566527] netif_receive_skb_list_internal+0x1116/0x17d0 [ 36.566710] napi_complete_done+0x376/0x740 [ 36.566918] virtnet_poll+0x1bae/0x2910 [ 36.567130] __napi_poll+0xf4/0x830 [ 36.567294] net_rx_action+0x97c/0x1ed0 [ 36.567556] handle_softirqs+0x306/0xe10 [ 36.567731] irq_exit_rcu+0x14c/0x2e0 [ 36.567910] do_io_irq+0xd4/0x120 [ 36.568139] io_int_handler+0xc2/0xe8 [ 36.568299] arch_cpu_idle+0xb0/0xc0 [ 36.568540] arch_cpu_idle+0x76/0xc0 [ 36.568726] default_idle_call+0x40/0x70 [ 36.568953] do_idle+0x1d6/0x390 [ 36.569486] cpu_startup_entry+0x9a/0xb0 [ 36.569745] rest_init+0x1ea/0x290 [ 36.570029] start_kernel+0x95e/0xb90 [ 36.570348] startup_continue+0x2e/0x40 [ 36.570703] [ 36.570798] Uninit was created at: [ 36.571002] kmem_cache_alloc_node_noprof+0x9e8/0x10e0 [ 36.571261] kmalloc_reserve+0x12a/0x470 [ 36.571553] __alloc_skb+0x310/0x860 [ 36.571844] __ip_append_data+0x483e/0x6a30 [ 36.572170] ip_append_data+0x11c/0x1e0 [ 36.572477] raw_sendmsg+0x1c8c/0x2180 [ 36.572818] inet_sendmsg+0xe6/0x190 [ 36.573142] __sys_sendto+0x55e/0x8e0 [ 36.573392] __s390x_sys_socketcall+0x19ae/0x2ba0 [ 36.573571] __do_syscall+0x12e/0x240 [ 36.573823] system_call+0x6e/0x90 [ 36.573976] [ 36.574017] Byte 35 of 98 is uninitialized [ 36.574082] Memory access of size 98 starts at 0000000007aa0012 [ 36.574218] [ 36.574325] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G B N 6.17.0-dirty #16 NONE [ 36.574541] Tainted: [B]=BAD_PAGE, [N]=TEST [ 36.574617] Hardware name: IBM 3931 A01 703 (KVM/Linux) [ 36.574755] ===================================================== [ 63.532541] ===================================================== [ 63.533639] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70 [ 63.533989] virtqueue_add+0x35c6/0x7c70 [ 63.534940] virtqueue_add_outbuf+0xa0/0xb0 [ 63.535861] start_xmit+0x288c/0x4a20 [ 63.536708] dev_hard_start_xmit+0x302/0x900 [ 63.537020] sch_direct_xmit+0x340/0xea0 [ 63.537997] __dev_queue_xmit+0x2e94/0x59b0 [ 63.538819] neigh_resolve_output+0x936/0xb40 [ 63.539793] ip_finish_output2+0x1ee2/0x2200 [ 63.540784] __ip_finish_output+0x272/0x7a0 [ 63.541765] ip_finish_output+0x4e/0x5e0 [ 63.542791] ip_output+0x166/0x410 [ 63.543771] ip_push_pending_frames+0x1a2/0x470 [ 63.544753] raw_sendmsg+0x1f06/0x2180 [ 63.545033] inet_sendmsg+0xe6/0x190 [ 63.546006] __sys_sendto+0x55e/0x8e0 ---truncated--- | ||||
| CVE-2023-54148 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Move representor neigh cleanup to profile cleanup_tx For IP tunnel encapsulation in ECMP (Equal-Cost Multipath) mode, as the flow is duplicated to the peer eswitch, the related neighbour information on the peer uplink representor is created as well. In the cited commit, eswitch devcom unpair is moved to uplink unload API, specifically the profile->cleanup_tx. If there is a encap rule offloaded in ECMP mode, when one eswitch does unpair (because of unloading the driver, for instance), and the peer rule from the peer eswitch is going to be deleted, the use-after-free error is triggered while accessing neigh info, as it is already cleaned up in uplink's profile->disable, which is before its profile->cleanup_tx. To fix this issue, move the neigh cleanup to profile's cleanup_tx callback, and after mlx5e_cleanup_uplink_rep_tx is called. The neigh init is moved to init_tx for symmeter. [ 2453.376299] BUG: KASAN: slab-use-after-free in mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.379125] Read of size 4 at addr ffff888127af9008 by task modprobe/2496 [ 2453.381542] CPU: 7 PID: 2496 Comm: modprobe Tainted: G B 6.4.0-rc7+ #15 [ 2453.383386] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 2453.384335] Call Trace: [ 2453.384625] <TASK> [ 2453.384891] dump_stack_lvl+0x33/0x50 [ 2453.385285] print_report+0xc2/0x610 [ 2453.385667] ? __virt_addr_valid+0xb1/0x130 [ 2453.386091] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.386757] kasan_report+0xae/0xe0 [ 2453.387123] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.387798] mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core] [ 2453.388465] mlx5e_rep_encap_entry_detach+0xa6/0xe0 [mlx5_core] [ 2453.389111] mlx5e_encap_dealloc+0xa7/0x100 [mlx5_core] [ 2453.389706] mlx5e_tc_tun_encap_dests_unset+0x61/0xb0 [mlx5_core] [ 2453.390361] mlx5_free_flow_attr_actions+0x11e/0x340 [mlx5_core] [ 2453.391015] ? complete_all+0x43/0xd0 [ 2453.391398] ? free_flow_post_acts+0x38/0x120 [mlx5_core] [ 2453.392004] mlx5e_tc_del_fdb_flow+0x4ae/0x690 [mlx5_core] [ 2453.392618] mlx5e_tc_del_fdb_peers_flow+0x308/0x370 [mlx5_core] [ 2453.393276] mlx5e_tc_clean_fdb_peer_flows+0xf5/0x140 [mlx5_core] [ 2453.393925] mlx5_esw_offloads_unpair+0x86/0x540 [mlx5_core] [ 2453.394546] ? mlx5_esw_offloads_set_ns_peer.isra.0+0x180/0x180 [mlx5_core] [ 2453.395268] ? down_write+0xaa/0x100 [ 2453.395652] mlx5_esw_offloads_devcom_event+0x203/0x530 [mlx5_core] [ 2453.396317] mlx5_devcom_send_event+0xbb/0x190 [mlx5_core] [ 2453.396917] mlx5_esw_offloads_devcom_cleanup+0xb0/0xd0 [mlx5_core] [ 2453.397582] mlx5e_tc_esw_cleanup+0x42/0x120 [mlx5_core] [ 2453.398182] mlx5e_rep_tc_cleanup+0x15/0x30 [mlx5_core] [ 2453.398768] mlx5e_cleanup_rep_tx+0x6c/0x80 [mlx5_core] [ 2453.399367] mlx5e_detach_netdev+0xee/0x120 [mlx5_core] [ 2453.399957] mlx5e_netdev_change_profile+0x84/0x170 [mlx5_core] [ 2453.400598] mlx5e_vport_rep_unload+0xe0/0xf0 [mlx5_core] [ 2453.403781] mlx5_eswitch_unregister_vport_reps+0x15e/0x190 [mlx5_core] [ 2453.404479] ? mlx5_eswitch_register_vport_reps+0x200/0x200 [mlx5_core] [ 2453.405170] ? up_write+0x39/0x60 [ 2453.405529] ? kernfs_remove_by_name_ns+0xb7/0xe0 [ 2453.405985] auxiliary_bus_remove+0x2e/0x40 [ 2453.406405] device_release_driver_internal+0x243/0x2d0 [ 2453.406900] ? kobject_put+0x42/0x2d0 [ 2453.407284] bus_remove_device+0x128/0x1d0 [ 2453.407687] device_del+0x240/0x550 [ 2453.408053] ? waiting_for_supplier_show+0xe0/0xe0 [ 2453.408511] ? kobject_put+0xfa/0x2d0 [ 2453.408889] ? __kmem_cache_free+0x14d/0x280 [ 2453.409310] mlx5_rescan_drivers_locked.part.0+0xcd/0x2b0 [mlx5_core] [ 2453.409973] mlx5_unregister_device+0x40/0x50 [mlx5_core] [ 2453.410561] mlx5_uninit_one+0x3d/0x110 [mlx5_core] [ 2453.411111] remove_one+0x89/0x130 [mlx5_core] [ 24 ---truncated--- | ||||
| CVE-2023-54160 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: firmware: arm_sdei: Fix sleep from invalid context BUG Running a preempt-rt (v6.2-rc3-rt1) based kernel on an Ampere Altra triggers: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46 in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 24, name: cpuhp/0 preempt_count: 0, expected: 0 RCU nest depth: 0, expected: 0 3 locks held by cpuhp/0/24: #0: ffffda30217c70d0 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248 #1: ffffda30217c7120 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248 #2: ffffda3021c711f0 (sdei_list_lock){....}-{3:3}, at: sdei_cpuhp_up+0x3c/0x130 irq event stamp: 36 hardirqs last enabled at (35): [<ffffda301e85b7bc>] finish_task_switch+0xb4/0x2b0 hardirqs last disabled at (36): [<ffffda301e812fec>] cpuhp_thread_fun+0x21c/0x248 softirqs last enabled at (0): [<ffffda301e80b184>] copy_process+0x63c/0x1ac0 softirqs last disabled at (0): [<0000000000000000>] 0x0 CPU: 0 PID: 24 Comm: cpuhp/0 Not tainted 5.19.0-rc3-rt5-[...] Hardware name: WIWYNN Mt.Jade Server [...] Call trace: dump_backtrace+0x114/0x120 show_stack+0x20/0x70 dump_stack_lvl+0x9c/0xd8 dump_stack+0x18/0x34 __might_resched+0x188/0x228 rt_spin_lock+0x70/0x120 sdei_cpuhp_up+0x3c/0x130 cpuhp_invoke_callback+0x250/0xf08 cpuhp_thread_fun+0x120/0x248 smpboot_thread_fn+0x280/0x320 kthread+0x130/0x140 ret_from_fork+0x10/0x20 sdei_cpuhp_up() is called in the STARTING hotplug section, which runs with interrupts disabled. Use a CPUHP_AP_ONLINE_DYN entry instead to execute the cpuhp cb later, with preemption enabled. SDEI originally got its own cpuhp slot to allow interacting with perf. It got superseded by pNMI and this early slot is not relevant anymore. [1] Some SDEI calls (e.g. SDEI_1_0_FN_SDEI_PE_MASK) take actions on the calling CPU. It is checked that preemption is disabled for them. _ONLINE cpuhp cb are executed in the 'per CPU hotplug thread'. Preemption is enabled in those threads, but their cpumask is limited to 1 CPU. Move 'WARN_ON_ONCE(preemptible())' statements so that SDEI cpuhp cb don't trigger them. Also add a check for the SDEI_1_0_FN_SDEI_PRIVATE_RESET SDEI call which acts on the calling CPU. [1]: https://lore.kernel.org/all/5813b8c5-ae3e-87fd-fccc-94c9cd08816d@arm.com/ | ||||
| CVE-2025-68367 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: macintosh/mac_hid: fix race condition in mac_hid_toggle_emumouse The following warning appears when running syzkaller, and this issue also exists in the mainline code. ------------[ cut here ]------------ list_add double add: new=ffffffffa57eee28, prev=ffffffffa57eee28, next=ffffffffa5e63100. WARNING: CPU: 0 PID: 1491 at lib/list_debug.c:35 __list_add_valid_or_report+0xf7/0x130 Modules linked in: CPU: 0 PID: 1491 Comm: syz.1.28 Not tainted 6.6.0+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__list_add_valid_or_report+0xf7/0x130 RSP: 0018:ff1100010dfb7b78 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffffa57eee18 RCX: ffffffff97fc9817 RDX: 0000000000040000 RSI: ffa0000002383000 RDI: 0000000000000001 RBP: ffffffffa57eee28 R08: 0000000000000001 R09: ffe21c0021bf6f2c R10: 0000000000000001 R11: 6464615f7473696c R12: ffffffffa5e63100 R13: ffffffffa57eee28 R14: ffffffffa57eee28 R15: ff1100010dfb7d48 FS: 00007fb14398b640(0000) GS:ff11000119600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010d096005 CR4: 0000000000773ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 80000000 Call Trace: <TASK> input_register_handler+0xb3/0x210 mac_hid_start_emulation+0x1c5/0x290 mac_hid_toggle_emumouse+0x20a/0x240 proc_sys_call_handler+0x4c2/0x6e0 new_sync_write+0x1b1/0x2d0 vfs_write+0x709/0x950 ksys_write+0x12a/0x250 do_syscall_64+0x5a/0x110 entry_SYSCALL_64_after_hwframe+0x78/0xe2 The WARNING occurs when two processes concurrently write to the mac-hid emulation sysctl, causing a race condition in mac_hid_toggle_emumouse(). Both processes read old_val=0, then both try to register the input handler, leading to a double list_add of the same handler. CPU0 CPU1 ------------------------- ------------------------- vfs_write() //write 1 vfs_write() //write 1 proc_sys_write() proc_sys_write() mac_hid_toggle_emumouse() mac_hid_toggle_emumouse() old_val = *valp // old_val=0 old_val = *valp // old_val=0 mutex_lock_killable() proc_dointvec() // *valp=1 mac_hid_start_emulation() input_register_handler() mutex_unlock() mutex_lock_killable() proc_dointvec() mac_hid_start_emulation() input_register_handler() //Trigger Warning mutex_unlock() Fix this by moving the old_val read inside the mutex lock region. | ||||
| CVE-2025-68752 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: iavf: Implement settime64 with -EOPNOTSUPP ptp_clock_settime() assumes every ptp_clock has implemented settime64(). Stub it with -EOPNOTSUPP to prevent a NULL dereference. The fix is similar to commit 329d050bbe63 ("gve: Implement settime64 with -EOPNOTSUPP"). | ||||
| CVE-2023-54117 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: s390/dcssblk: fix kernel crash with list_add corruption Commit fb08a1908cb1 ("dax: simplify the dax_device <-> gendisk association") introduced new logic for gendisk association, requiring drivers to explicitly call dax_add_host() and dax_remove_host(). For dcssblk driver, some dax_remove_host() calls were missing, e.g. in device remove path. The commit also broke error handling for out_dax case in device add path, resulting in an extra put_device() w/o the previous get_device() in that case. This lead to stale xarray entries after device add / remove cycles. In the case when a previously used struct gendisk pointer (xarray index) would be used again, because blk_alloc_disk() happened to return such a pointer, the xa_insert() in dax_add_host() would fail and go to out_dax, doing the extra put_device() in the error path. In combination with an already flawed error handling in dcssblk (device_register() cleanup), which needs to be addressed in a separate patch, this resulted in a missing device_del() / klist_del(), and eventually in the kernel crash with list_add corruption on a subsequent device_add() / klist_add(). Fix this by adding the missing dax_remove_host() calls, and also move the put_device() in the error path to restore the previous logic. | ||||