Export limit exceeded: 397474 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (397474 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-93273 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: regulator: tps6594: Fix device node reference leaks in multiphase loop In tps6594_regulator_probe(), the multi-phase configuration loop calls of_find_node_by_name() to find buck nodes by name, and of_get_parent() twice to navigate to the PMIC parent node. None of the acquired node references (np, intermediate parent, np_pmic_parent) are ever released via of_node_put(), causing a reference leak on every loop iteration. Additionally, of_find_node_by_name() can return NULL, but the result was immediately passed to of_node_full_name() and of_get_parent() without a NULL check, which could lead to a NULL pointer dereference. Fix this by: - Adding a NULL check for np after of_find_node_by_name() - Storing the intermediate parent node in a local variable np_parent - Calling of_node_put() on np, np_parent and np_pmic_parent at the end of each loop iteration | ||||
| CVE-2026-93272 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: remoteproc: qcom_wcnss: Fix handling the lack of PD regulators in v3 The changes introduced to handle single power domain platforms have swapped the info pointer increment from num_pd_vregs to num_pds, which would shift the info pointer past the end of the array for pronto-v3, which does not list power domain regulators in vregs. This showed up as a difference between GCC- and LLVM-compiled kernels on SDM632 devices, where only with LLVM one would get the "regulator request with no identifier" error, because the out-of-bounds memory ended up being zeroed. Fix by skipping the increment when there are more power domains than regulators. | ||||
| CVE-2026-93271 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: cap out-of-range rx MCS instead of leaving bogus rate ath11k can receive HT/VHT/HE frames whose reported MCS is above the maximum that can be expressed in the corresponding mac80211 rate space (e.g. an HE frame reported with MCS 12, while HE tops out at MCS 11). The frame itself is valid and decodes correctly, but for such a frame ath11k_dp_rx_h_rate() leaves rx_status->rate_idx set to the out-of-range value and never assigns rx_status->encoding, so it stays RX_ENC_LEGACY from the ath11k_dp_rx_h_ppdu() initialization. Once that frame reaches mac80211 it trips the rate sanity check and the frame is dropped with a splat: ath11k_pci 0000:03:00.0: Received with invalid mcs in HE mode 12 WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:5433 ieee80211_rx_list+0xb0a/0xe90 [mac80211] Dropping the frame would discard otherwise valid data, so instead cap the reported MCS to the maximum the rate space can express and deliver the frame. Set rx_status->encoding before the range check and assign rate_idx from the capped value, so a frame with an out-of-range MCS no longer leaves partial or bogus rate metadata behind. Also downgrade the logging level since they are not treated as invalid frames now. The only loss is that such a frame is reported as the capped MCS in the rx rate statistics. Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.41 | ||||
| CVE-2026-93270 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Disallow interpreter fallback for BPF_ADDR_PERCPU insn The BPF_MOV64_PERCPU_REG insn requires JIT to emit native code to for 'dst_reg = src_reg + <percpu_base_off>'. However, the interpreter ignores the 'off' at its ALU64_MOV_X label. The 'off' indicates the insn is BPF_MOV64_PERCPU_REG insn. Then, when the interpreter loads memory from the register, it will hit a page fault. [ 2.545572] BUG: unable to handle page fault for address: ffffffffacaaf034 [ 2.546485] #PF: supervisor read access in kernel mode [ 2.547167] #PF: error_code(0x0000) - not-present page [ 2.547850] PGD 134e63067 P4D 134e63067 PUD 134e64063 PMD 10021c063 PTE 800ffffeca550062 [ 2.548912] Oops: Oops: 0000 [#1] SMP PTI Set jit_required as true in order to disallow interpreter fallback in core.c::__bpf_prog_select_runtime(), if any BPF_ADDR_PERCPU insn is patched to the prog. BTW, rename the helper bpf_map_supports_cpu_flags() to bpf_map_is_percpu_map(). | ||||
| CVE-2026-93269 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix circular lock dependency in ext4_ext_migrate Move iput(tmp_inode) after ext4_writepages_up_write() to avoid a circular lock dependency between s_writepages_rwsem and sb_internal (freeze protection). The deadlock scenario: CPU0 (EXT4_IOC_MIGRATE) CPU1 (orphan cleanup during mount) ---- ---- ext4_ext_migrate() ext4_writepages_down_write() s_writepages_rwsem (write) ext4_evict_inode() sb_start_intwrite() [sb_internal] ... ext4_writepages() s_writepages_rwsem (read) [BLOCKED] iput(tmp_inode) ext4_evict_inode() sb_start_intwrite() [BLOCKED] The tmp_inode is a temporary inode with nlink=0 created solely for building the extent tree. Its eviction does not require s_writepages_rwsem protection, so deferring iput() until after releasing the rwsem is safe. | ||||
| CVE-2026-93268 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ext4: skip extra isize expansion during mount to prevent deadlock ext4_try_to_expand_extra_isize() is called from __ext4_mark_inode_dirty() while holding an active jbd2 handle. During mount (!SB_ACTIVE), the expand path may move xattrs to external blocks and release ea_inodes via iput(). When !SB_ACTIVE, iput() calls write_inode_now() which acquires s_writepages_rwsem, creating a circular lock dependency: s_writepages_rwsem --> jbd2_handle --> xattr_sem --> s_writepages_rwsem This can be triggered via: ext4_process_orphan() -> ext4_truncate() -> ext4_mark_inode_dirty() -> ext4_try_to_expand_extra_isize() or: ext4_evict_inode() -> ext4_mark_inode_dirty() -> ext4_try_to_expand_extra_isize() Skip expansion when !SB_ACTIVE. This is a minor loss of functionality (extra isize won't grow for these inodes during mount), which e2fsck can resolve later if needed. | ||||
| CVE-2026-93267 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix potential use after free in uverbs_free_dmah() When accessing a dmah via the netlink path the only synchronization mechanism for the said dmah is rdma_restrack_get(). Currently, rdma_restrack_del() is invoked at the end of uverbs_free_dmah(), which is too late, since by that point vendor-specific resources associated with the dmah might already be freed. This can leave a short window where the dmah remains accessible through restrack, leading to a potential use-after-free. Fix this by moving the rdma_restrack_begin_del() call to the start of uverbs_free_dmah(), ensuring that the dmah is removed from restrack before its internal resources are released. This guarantees that no new users hold references to a dmah that is in the process of destruction. In addition, this change preserves the intended inverted order between create and destroy routines: resources are added to restrack at the end of successful creation, and hence shall be removed from the restrack first thing during the destruction flow, which keeps the lifecycle management consistent and predictable. | ||||
| CVE-2026-93266 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: arm64: RSI: fix field-spanning write warning in attestation token init The challenge is passed in registers a1 through a8. However, copying to ®s.a1 makes FORTIFY treat the destination as the single a1 field, resulting in a field-spanning write warning. [1] Overlay the SMCCC register structure with an RSI-specific argument layout and copy the challenge into an explicit 64-byte array. This keeps the existing a1-a8 argument encoding while giving the copy a correctly sized destination object. [1] memcpy: detected field-spanning write (size 64) of single field "®s.a1" at ./arch/arm64/include/asm/rsi_cmds.h:119 (size 8) WARNING: ./arch/arm64/include/asm/rsi_cmds.h:119 at rsi_attestation_token_init+0xdc/0xf8 [arm_cca_guest], CPU#0: cat/3314 | ||||
| CVE-2026-93265 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: PCI/pwrctrl: tc9563: Fix parsing the integrated Ethernet MAC Endpoint node DSP3 has an integrated Ethernet MAC Endpoint which has its own set of config registers for configuring settings such as ASPM. The Endpoint device has two physical functions and those two functions share the same settings. Parse the Endpoint node under DSP3 instead of parsing both functions. The existing parsing logic also has one OOB issue as parsing both functions will result in accessing past the tc9563_pwrctrl->cfg array. | ||||
| CVE-2026-93264 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/efa: Fix PBL chunk length computation On register MR, when creating the PBL, if it's an indirect PBL we create a chunk list to hold the PBL pages pointers. Each chunk is 4KB in size and can hold 510 addresses (EFA_PTRS_PER_CHUNK) and has a 12-byte control buffer at the end of it holding the next chunk's pointer and its length. If the PBL number of pages is a multiple of EFA_PTRS_PER_CHUNK, the calculated last chunk length is wrongly computed as 0, even though that chunk is fully populated with 510 real page pointers. This wrong length is used both to DMA map the chunk and is propagated to the device, causing the device to see the chunk as empty and reject the memory registration. Fix the calculation so it will be performed only if the number of pages isn't a multiple of EFA_PTRS_PER_CHUNK, if it is, its already handled in the above loop correctly. Also prevent out-of-bounds reach in the chunks array in such scenario. | ||||
| CVE-2026-93263 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: clk: eswin: Zero-initialize stack-allocated clk_init_data eswin_clk_register_pll() and eswin_register_clkdiv() declare a struct clk_init_data on the stack and only initialize some of its fields (parent_data respectively parent_hws). clk_core_populate_parent_map() checks parent_names first and parent_data second before falling back to parent_hws, so leftover stack garbage in the uninitialized fields hijacks parent resolution and the clk core dereferences a bogus pointer: Unable to handle kernel NULL pointer dereference at virtual address 000000000000000c Oops [#1] epc : __clk_register+0x31a/0x7f0 [<ffffffff805dc774>] __clk_register+0x31a/0x7f0 [<ffffffff805dcd76>] devm_clk_hw_register+0x2a/0x94 [<ffffffff805e319a>] eswin_register_clkdiv+0x80/0xd0 [<ffffffff805e34a0>] eswin_clk_register_clks+0x162/0x1a0 [<ffffffff805e3736>] eic7700_clk_probe+0x146/0x180 [<ffffffff8065d23c>] platform_probe+0x3c/0x7a Observed on EIC7700 hardware (with the driver backported to a 6.17 tree); whether the bug triggers depends entirely on what the stack happens to contain when the registration helpers run. Zero-initialize both structures. | ||||
| CVE-2026-93262 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: md/raid5-ppl: fix use-after-free in ppl_do_flush() The loop in ppl_do_flush() continues iterating after calling ppl_io_unit_finished(), touching io->pending_flushes and leading to a use-after-free. Add a break statement to stop the loop once io is freed. | ||||
| CVE-2026-93261 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: locking/lockdep: Fix NULL pointer dereference in __lock_set_class() register_lock_class() can return NULL when the lock class pool is exhausted, graph_lock() fails, or key validation fails. However, __lock_set_class() uses the return value directly in pointer arithmetic without a NULL check: class = register_lock_class(lock, subclass, 0); hlock->class_idx = class - lock_classes; If class is NULL, this computes a wild offset that corrupts hlock->class_idx. The subsequent reacquire_held_locks() call will invoke hlock_class() with this corrupted index, leading to a NULL or out-of-bounds pointer dereference. Add the missing NULL check, consistent with how __lock_acquire() already handles this case at the same call site. | ||||
| CVE-2026-88365 | 2026-09-24 | N/A | ||
| minimp3 commit ea99364f contains an integer overflow vulnerability in mp3dec_skip_id3v1() when parsing the APEv2 tag-size field. | ||||
| CVE-2026-93260 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: powerpc/xive: propagate IPI init errors to prevent use-after-free When xive_init_ipis() fails (e.g. irq_domain_alloc_irqs() fails), the error path frees the global xive_ipis array. However, xive_smp_probe() previously ignored this failure and proceeded to call xive_setup_cpu_ipi(), which dereferences the already-freed xive_ipis pointer -- a use-after-free. Now that xive_smp_probe() returns int (previous patch), propagate the error from xive_init_ipis() and xive_setup_cpu_ipi() through xive_smp_probe(). Check the return value in both pnv_smp_probe() and pSeries_smp_probe() so that IPI setup is aborted cleanly on failure, avoiding the use-after-free. | ||||
| CVE-2026-93259 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: powerpc/irq: Fix missing r2 clobber in PCREL inline assembly In CONFIG_PPC_KERNEL_PCREL mode, r2 is no longer reserved for the TOC pointer and is available as a caller-saved register [0]. Both call_do_irq() and call_do_softirq() use inline assembly to call functions with stack switching, but fail to list r2 in their clobber lists. This causes the compiler to assume r2 is preserved across these calls, leading to register corruption when the called functions (__do_irq and __do_softirq) clobber r2. As a result of this kernel crash during interrupt handling is seen and the kernel fails to boot: BUG: Unable to handle kernel data access on write at 0xc000000404697638 Faulting instruction address: 0xc0000000000181ec Oops: Kernel access of bad area, sig: 11 [#1] NIP [c0000000000181ec] __do_IRQ+0x6c/0xc0 With older GCC, the compiler would conservatively allocate callee-saved registers (like r31) for values spanning function calls, accidentally avoiding the bug: <__do_IRQ>: 00 00 00 60 nop a6 02 08 7c mflr r0 f8 ff e1 fb std r31,-8(r1) f0 ff c1 fb std r30,-16(r1) 2d 03 10 06 pla r31,53297316 ... 3d e8 ff 4b bl c0000000000165ac <__do_irq> 00 00 21 e8 ld r1,0(r1) 28 00 4d e9 ld r10,40(r13) 40 00 21 38 addi r1,r1,64 2a f9 aa 7f stdx r29,r10,r31 With newer GCC 14, the compiler uses r2 for such values, exposing the missing clobber specification: <__do_IRQ>: 00 00 00 60 nop a6 02 08 7c mflr r0 f0 ff c1 fb std r30,-16(r1) f8 ff e1 fb std r31,-8(r1) 29 02 10 06 pla r2,36252592 # c0000000022aadc0 <__irq_regs> ... 85 dc ff 4b bl c000000000015ee0 <__do_irq> 00 00 21 e8 ld r1,0(r1) 28 00 2d e9 ld r9,40(r13) 30 00 21 38 addi r1,r1,48 2a 11 c9 7f stdx r30,r9,r2 Fix this by adding r2 to the clobber list for both call_do_irq() and call_do_softirq() when CONFIG_PPC_KERNEL_PCREL is enabled. [0]: https://www.mail-archive.com/gcc-patches@gcc.gnu.org/msg313226.html | ||||
| CVE-2026-45528 | 1 Google | 1 Android | 2026-09-24 | 7.3 High |
| In getManageSpaceActivityIntent of StorageManagerService.java, there is a possible LaunchAnyWhere chain due to an unsafe PendingIntent. This could lead to local escalation of privilege with no additional execution privileges needed. User interaction is needed for exploitation. | ||||
| CVE-2026-93258 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ocfs2: do not use make_bad_inode() in ocfs2_read_inode_block_full() This reverts commit 58b6fcd2ab34 ("ocfs2: mark inode bad upon validation failure during read"). Since 'make_bad_inode()' resets inode type to S_IFREG, doing this for directory inode during active VFS lookup is likely to confuse the latter, including VFS_BUG_ON_INODE() triggered in this case. | ||||
| CVE-2023-0288 | 4 Apple, Fedoraproject, Neovim and 1 more | 4 Macos, Fedora, Neovim and 1 more | 2026-09-24 | 7.8 High |
| Heap-based Buffer Overflow in GitHub repository vim/vim prior to 9.0.1189. | ||||
| CVE-2026-93257 | 1 Linux | 1 Linux Kernel | 2026-09-24 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: block: handle nogenerate/noverify properly in fs-integrity Check the BIP_CHECK flags before generating or verifying PI information, otherwise this can be incorrectly called for non-PI metadata and cause generation of incorrect metadata and crashed in the verification handler. The new behavior matches that of the block layer auto-generated metadata. | ||||