| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: validate assoc response length before status and IE access
cfg80211_rx_assoc_resp() initialises the status and response-IE fields
of cfg80211_connect_resp_params from the management frame before
proving that the frame is long enough for those offsets. S1G and
regular association responses also have different IE offsets, but the
S1G path only patched resp_ie after the unsafe initialiser had already
run.
Defer resp_ie, resp_ie_len, and status to after the link-iteration
loop. Use a bool to remember whether the frame is S1G, then validate
the appropriate minimum length and set all three fields in a single
if/else block. Funnel short-frame and SME-reject cleanup through a
shared free_bss label for the abandon paths. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix use-after-free on reloc root after error in insert_dirty_subvol()
If during relocation we fail in insert_dirty_subvol() because
btrfs_update_reloc_root() returned an error, we will leave a root's
reloc_root field pointing to a reloc root that was freed instead of NULL,
resulting later in a use-after-free, or double free attempt during
unmount.
The sequence of steps is this:
1) During relocation the call to btrfs_update_reloc_root() in
insert_dirty_subvol() fails, so insert_dirty_subvol() returns the
error to merge_reloc_root() without adding the root to the list
rc->dirty_subvol_roots;
2) Then merge_reloc_root() aborts the current transaction because
insert_dirty_subvol() returned an error;
3) Up the call chain, merge_reloc_roots() gets the error, adds the
reloc root for root X to the local reloc_roots list and jumps to the
'out' label, where it calls free_reloc_roots() to free all the reloc
roots in the local reloc_roots list. This frees the reloc root for
root X;
4) We go up the call chain to relocate_block_group() which calls
clean_dirty_subvols() to go over dirty roots and set their
->reloc_root field to NULL, but root X is not in the dirty_subvol_roots
list, so its ->reloc_root still points to a reloc root;
5) Relocation finishes, with an error and a transaction abort, but the
->reloc_root field for root X still points to the reloc root that was
freed in step 3;
6) When unmounting the fs we end up calling:
btrfs_free_fs_roots()
btrfs_drop_and_free_fs_root()
--> calls btrfs_put_root() against root X's ->reloc_root
which is not NULL and points to the already freed
reloc root in step 4 above
Resulting in a use-after-free to a double free attempt.
Syzbot reported this with the following dmesg/syslog:
[ 106.004389][ T5339] BTRFS error (device loop0 state A): Transaction aborted (error -5)
[ 106.014266][ T5339] BTRFS: error (device loop0 state A) in merge_reloc_root:1655: errno=-5 IO failure
[ 106.021891][ T1061] BTRFS error (device loop0 state A): error while writing out transaction: -5
[ 106.026964][ T1061] BTRFS warning (device loop0 state A): Skipping commit of aborted transaction.
[ 106.033807][ T5340] BTRFS error (device loop0 state A): bdev /dev/loop0 errs: wr 3, rd 0, flush 0, corrupt 0, gen 0
[ 106.039265][ T1061] BTRFS: error (device loop0 state A) in cleanup_transaction:2067: errno=-5 IO failure
[ 106.044382][ T5339] BTRFS info (device loop0 state EA): forced readonly
[ 106.074329][ T5339] BTRFS: error (device loop0 state EA) in merge_reloc_roots:1887: errno=-5 IO failure
[ 106.081004][ T5356] BTRFS info (device loop0 state EA): scrub: started on devid 1
[ 106.085611][ T5339] BTRFS info (device loop0 state EA): balance: ended with status: -30
[ 106.089517][ T5356] BTRFS info (device loop0 state EA): scrub: not finished on devid 1 with status: -30
[ 106.662365][ T5338] BTRFS info (device loop0 state EA): last unmount of filesystem 3a375e4e-b156-4d76-a2ad-16e198ce1409
[ 106.682946][ T5338] ==================================================================
[ 106.686574][ T5338] BUG: KASAN: slab-use-after-free in btrfs_put_root+0x2f/0x250
[ 106.690090][ T5338] Write of size 4 at addr ffff88803f978630 by task syz.0.0/5338
[ 106.693173][ T5338]
[ 106.694279][ T5338] CPU: 0 UID: 0 PID: 5338 Comm: syz.0.0 Not tainted syzkaller #0 PREEMPT(full)
[ 106.694293][ T5338] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 106.694300][ T5338] Call Trace:
[ 106.694308][ T5338] <TASK>
[ 106.694314][ T5338] dump_stack_lvl+0xe8/0x150
[ 106.694331][ T5338] print_address_description+0x55/0x1e0
[ 106.694343][ T5338] ? btrfs_put_root+0x2f/0x250
[ 106.694358][ T5338] print_report+0x58/0x70
[ 106.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: validate sta_id in BA window status notif
BA_WINDOW_STATUS_NOTIFICATION_ID extracts a 5-bit sta_id from the
firmware notification and uses it to index fw_id_to_mac_id[] without
bounds checking. Validate sta_id before array access to prevent
out-of-bounds indexing. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix reloc root cleanup in merge_reloc_roots()
If the root we got has zero root refs in its root item, we are resetting
the root's ->reloc_root without using barriers like we do everywhere else.
Sashiko complained about this while reviewing another patch, and it's
correct (see the Link tag below).
Also, we should not clear BTRFS_ROOT_DEAD_RELOC_TREE from the root unless
the root points to the reloc root we have.
Fix this by using clear_reloc_root(), which issues the memory barrier
after setting the root's ->reloc_root to NULL and before clearing the bit
BTRFS_ROOT_DEAD_RELOC_TREE from the root. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: bound dirent name against end of SMB response in cifs_filldir
cifs_filldir() copies the entry name out of an SMB1 TRANS2_FIND_FIRST /
FIND_NEXT response using a length (de.namelen) supplied by the server.
The kmalloc'd SMB response buffer is bounded, but nothing checks that
de.name + de.namelen still lies inside that buffer before the eventual
filldir64() -> verify_dirent_name() -> memchr() reads namelen bytes.
A hostile SMB1 server that returns an oversized FileNameLength in a
directory entry therefore causes memchr() to read past the end of the
response slab buffer. Reachable from any user who can list a directory
on a CIFS mount served by an attacker-controlled server (getdents64()
on the mounted directory):
BUG: KASAN: slab-out-of-bounds in memchr+0x71/0x80
Read of size 1 at addr ffff88800e0640cc by task poc/115
Call Trace:
dump_stack_lvl+0x64/0x80
print_report+0xce/0x620
kasan_report+0xec/0x120
memchr+0x71/0x80
filldir64+0x4c/0x6a0
cifs_filldir.constprop.0+0x9bb/0x1e00
cifs_readdir+0x2101/0x3380
iterate_dir+0x19c/0x520
__x64_sys_getdents64+0x126/0x210
do_syscall_64+0x107/0x5a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Pass the end-of-response pointer down to cifs_filldir() and reject
entries whose name would extend past that boundary.
This bug was discovered by Artiphishell's vTriage pipeline, which
generated a userspace reproducer (an emulated hostile SMB1 server plus
a getdents64() client) that reliably triggers the KASAN report on an
unpatched kernel. The fix below was drafted with the Claude coding
assistant; a userspace reproducer is available on request. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-scsi: flush backend after device ioctls
vhost-scsi translates guest response descriptors into userspace iovecs
when commands are submitted. Target-core completes those commands
asynchronously, so VHOST_SET_MEM_TABLE can replace the memory table while
an in-flight command still retains response iovecs translated through the
old table.
If the old mapping is reused after VHOST_SET_MEM_TABLE returns, command
completion can write the response to an unrelated userspace object.
Flush the vhost-scsi backend after vhost_dev_ioctl() handles a device
ioctl. This waits for in-flight commands that can still use the old
response iovecs before the ioctl returns. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: smbus: reject oversized block transfers in the common path
The SMBus block transfer length data->block[0] is validated in
i2c_smbus_xfer_emulated() but that check runs too late for tracepoints
and is skipped entirely when the adapter provides a native smbus_xfer
implementation. This allows user-controlled oversized block lengths to
reach tracepoint memcpy calls and driver callbacks unchecked.
Add an early validation in __i2c_smbus_xfer() that rejects block
transfers whose caller-supplied length is zero or exceeds
I2C_SMBUS_BLOCK_MAX before any tracepoint fires or driver callback
runs. data->block[0] is filled in by the device on SMBus block reads,
so the check is scoped to operations where the length is actually
supplied by the caller. This is consistent with the existing -EINVAL
convention in the emulated path and protects all downstream consumers
at once: the smbus_write tracepoint, all native smbus_xfer driver
implementations, and the emulated path.
Two distinct bugs are fixed by this change:
Bug 1: smbus_write tracepoint OOB (include/trace/events/smbus.h)
trace_smbus_write() fires before any validation and copies
data->block[0]+1 bytes into a 34-byte event buffer. With
block[0]=0xfe the tracepoint copies 255 bytes, overflowing by 221.
BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_smbus_write+0x27c/0x530
Read of size 255 at addr ffff88800d98fcf8 by task poc_smbus/91
Call Trace:
<TASK>
__asan_memcpy+0x23/0x80
trace_event_raw_event_smbus_write+0x27c/0x530
__i2c_smbus_xfer+0x43a/0xa40
i2c_smbus_xfer+0x19e/0x340
i2cdev_ioctl_smbus+0x38f/0x7f0
i2cdev_ioctl+0x35e/0x680
__x64_sys_ioctl+0x147/0x1e0
do_syscall_64+0xcf/0x15a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Bug 2: i2c-stub I2C_SMBUS_I2C_BLOCK_DATA OOB (drivers/i2c/i2c-stub.c)
stub_xfer() implements .smbus_xfer directly and only clamps
block[0] against 256-command, not I2C_SMBUS_BLOCK_MAX. With
block[0]=0xff and command=0 the loop accesses block[1+i] for
i up to 254, far past the 34-byte union.
UBSAN: array-index-out-of-bounds in drivers/i2c/i2c-stub.c:223:44
index 34 is out of range for type '__u8 [34]'
Call Trace:
<TASK>
__ubsan_handle_out_of_bounds+0xd7/0x120
stub_xfer+0x1971/0x198f [i2c_stub]
__i2c_smbus_xfer+0x306/0xa40
i2c_smbus_xfer+0x19e/0x340
i2cdev_ioctl_smbus+0x38f/0x7f0
i2cdev_ioctl+0x35e/0x680
__x64_sys_ioctl+0x147/0x1e0
do_syscall_64+0xcf/0x15a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Both traces reproduced on v7.0-rc6+i2c/for-current with KASAN+UBSAN. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/pagemap: dma-unmap pages before handling migration errors
drm_pagemap_migrate_unmap_pages() relies on the pages array to determine
which pages require DMA unmapping. However,
drm_pagemap_migration_unlock_put_pages() clears the array as part of its
cleanup, leaving drm_pagemap_migrate_unmap_pages() with no valid page
information if it is called afterward.
Call drm_pagemap_migrate_unmap_pages() before
drm_pagemap_migration_unlock_put_pages() so the pages array remains
valid during DMA unmapping. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: skip the zoned limits update if the zone info query failed
nvme_query_zone_info() returns either a negative errno or a positive
NVMe status code, but nvme_update_ns_info_block() only tests for the
negative case:
ret = nvme_query_zone_info(ns, lbaf, &zi);
if (ret < 0)
goto out;
If the device fails the Identify Namespace (I/O Command Set specific)
command, or the Identify Controller command issued by
nvme_set_max_append(), the positive status falls through and setup
continues with the zero-initialized zone info. nvme_update_zone_info()
then marks the queue zoned with chunk_sectors and ns->head->zsze set to
zero.
blk_validate_zoned_limits() does not check chunk_sectors, so the limits
commit succeeds. blk_revalidate_disk_zones() does reject the zero zone
size, but by then the limits are live and nothing rolls them back, so
I/O keeps being submitted to a zoned queue with a zero zone size and
disk_zone_no() shifts by ilog2(0):
nvme0n1: Invalid non power of two zone size (0)
UBSAN: shift-out-of-bounds in include/linux/blkdev.h:747:16
shift exponent -1 is negative
disk_zone_no include/linux/blkdev.h:747 [inline]
bio_straddles_zones include/linux/blkdev.h:1058 [inline]
blk_zone_wplug_handle_write block/blk-zoned.c:1423 [inline]
blk_zone_plug_bio.cold+0x25/0x1c8 block/blk-zoned.c:1605
blk_mq_submit_bio+0x18fb/0x2870 block/blk-mq.c:3196
submit_bh_wbc+0x575/0x740 fs/buffer.c:2824
__block_write_full_folio+0x728/0xdd0 fs/buffer.c:1933
Any device, firmware or NVMe-oF target that fails this one command
reaches this.
Skip the zoned limits update in that case, and log which of the two
things happened: during a revalidation the queue keeps the zone
geometry it was last validated with, and on a first scan the namespace
is registered without zoned limits, so that it is still available as a
handle for admin commands. Neither of the paths in
nvme_query_zone_info() that return a positive status logs anything, so
the failure would otherwise be silent.
zi.zone_size is an exact indicator: every path that returns a positive
status returns before it is assigned, and after that the only failure
left is -ENODEV, which the caller already handles.
Found by FuzzNvme. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: prevent out-of-bounds reads in share config responses
Validate IPC share configuration payload sizes before consuming
variable-length fields. Bound veto list parsing and account for
the separator byte when deriving the path length. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: gadget: Fix use-after-free in dwc3_gadget_free_endpoints due to race condition
In dwc3_gadget_init_endpoint, &dep->nostream_work is bound with
dwc3_nostream_work, and dwc3_gadget_endpoint_stream_event can queue
this delayed work on system_percpu_wq when a DEPEVT_STREAM_NOSTREAM
event is received.
If we remove the gadget, dwc3_gadget_free_endpoints makes cleanup and
the memory allocated for dep with kzalloc() is released by kfree(dep),
while the delayed work mentioned above may still be pending or
running. The sequence of operations that may lead to a UAF bug is as
follows:
CPU0 CPU1
| dwc3_thread_interrupt
| dwc3_endpoint_interrupt
| dwc3_gadget_endpoint_stream_event
| queue_delayed_work(system_percpu_wq,
| &dep->nostream_work)
dwc3_gadget_free_endpoints |
dwc3_free_trb_pool(dep) |
list_del(&dep->endpoint.ep_list) |
dwc3_debugfs_remove_endpoint_dir(dep) |
kfree(dep) |
// dep is freed |
| dwc3_nostream_work
| // use dep (use-after-free)
Fix it by canceling the delayed work before kfree(dep) in
dwc3_gadget_free_endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
landlock: Require LANDLOCK_ACCESS_FS_MAKE_REG for whiteout creation
Whiteout objects are used in the upper layer of an OverlayFS to
indicate that the file with this name does not exist in the unified
view, even if it is present in one of the lower layer file systems.
For the userspace implementations of OverlayFS (fuse-overlayfs),
whiteout objects can be created from userspace as well:
* mknod(2) with S_IFCHR and makedev(0, 0)
* renameat2(2) with RENAME_WHITEOUT,
creating the whiteout in the old place of the moved file.
This commit guards whiteout creation in both of these cases with
LANDLOCK_ACCESS_FS_MAKE_REG. Whiteout objects are *not* considered
character devices and are not bound to a driver.
LANDLOCK_ACCESS_FS_MAKE_REG describes the same permission class as a
whiteout object: creating one is the only S_IFCHR creation that the VFS
exempts from CAP_MKNOD, so it is as unprivileged as creating a regular
file, while LANDLOCK_ACCESS_FS_MAKE_CHAR and
LANDLOCK_ACCESS_FS_MAKE_BLOCK keep meaning the creation of devices that
expose a kernel interface [1].
For the mknod(2) case, introduce a Landlock erratum. The creation of
whiteout objects through mknod(2) was previously guarded using
LANDLOCK_ACCESS_FS_MAKE_CHAR, and it is now guarded using
LANDLOCK_ACCESS_FS_MAKE_REG.
For the renameat2(2) case, fix a bug: Before this commit, renameat2(2)
with RENAME_WHITEOUT would create a directory entry even when all
LANDLOCK_ACCESS_FS_MAKE_* rights were denied.
This does not affect normal renames within layered OverlayFS mounts:
When doing a regular rename() on a mounted fuse-overlayfs, it is the
fuse-overlayfs daemon that exercises renameat2() with RENAME_WHITEOUT,
and only the Landlock domain of that daemon is checked there.
Depends-on: 49c9e09d9610 ("landlock: Fix handling of disconnected directories")
Depends-on: fe72ce6710cb ("landlock: Add errata documentation section")
[mic: Record why LANDLOCK_ACCESS_FS_MAKE_REG is the matching right, and
add link(2) to the user doc] |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Fix subbuf resize race with ring_buffer_alloc_read_page()
ring_buffer_alloc_read_page() is racy with ring_buffer_subbuf_order_set,
it can allocate a reader page with an outdated order. This isn't a big
issue, the user can still re-allocate a new reader page and try again.
However, what is more problematic is if the value of subbuf_order
changes in the middle of ring_buffer_alloc_read_page(). In that case,
bpage->order might not match the actual allocated memory.
Use bpage->order for the allocation to prevent this race. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Make cpu_buffer::free_page a buffer_data_read_page
Discarding a cached reader page after a concurrent ring buffer resize
uses the new global subbuf_order for the free_pages() call. This
mismatched order may crashes the kernel or leaks memory because the cached
page was allocated under the old size.
Save the actual free_page order alongside the page address to ensure we
always refer to the correct value and do not rely on the potentially
stalled cpu_buffer->subbuf_order value. The simplest is to make
free_page a buffer_data_read_page which already covers exactly what we
need: a page address and a page order. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Fix UAF in selftest IOPF reporting
IOMMUFD selftest TRIGGER_IOPF borrows an attach handle from
group->pasid_array without synchronizing against PASID detach,
then a concurrent iommu_report_device_fault() can dereference
that borrowed handle's domain pointer after the detach erases
the handle and frees the backing struct iommufd_attach_handle.
TRIGGER_IOPF then dereferences the freed handle, causing a UAF.
Fix by adding a iopf_rwsem in mock_dev to follow the expected design
of a real driver. Hold its read side across the whole
iommu_report_device_fault() call, and its write side around every
path that attaches, detaches, or replaces a device domain.
This can block new reports and drains in-flight reports before an old
attach handle or the IOPF fault parameter can be removed.
Also take the write side while registering a mock device, since
it can invoke the mock driver's default-domain attach callback. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86/amd/pmc: Fix LPS0 and debugfs leaks when STB init fails
amd_pmc_probe() registers the LPS0 s2idle handler with
acpi_register_lps0_dev() and creates the driver's debugfs directory before
calling amd_stb_s2d_init(), which is the last step in probe that can fail.
When amd_stb_s2d_init() fails (for example the S2D telemetry region cannot
be ioremapped on a long-running system, or the SMU rejects the S2D setup)
the error path only calls pci_dev_put() and returns. This leaves
amd_pmc_s2idle_dev_ops on the global lps0_s2idle_devops_head list and leaks
the debugfs directory, while the devm-managed resources backing the handler
are torn down.
Reloading the module then walks the corrupted list in
acpi_register_lps0_dev() and hits:
list_add corruption. next->prev should be prev, but was NULL.
kernel BUG at lib/list_debug.c:29!
acpi_register_lps0_dev+0x44/0x80
amd_pmc_probe+0x224/0x380 [amd_pmc]
platform_probe+0x67/0x90
Even without a reload, the stale registration means the next s2idle
transition calls into torn-down driver state.
Unwind the debugfs directory and the LPS0 registration on the
amd_stb_s2d_init() error path. acpi_unregister_lps0_dev() is safe to call
unconditionally here: it is guarded on the same conditions as
acpi_register_lps0_dev(), which is exactly what amd_pmc_remove() already
relies on. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Unlink scc_entry in unix_del_edge().
Kyle Zeng reported that GC could free a dead SCC partially.
The scenario is as follows:
1) Create two SCCs:
X -. A <-> B
^--'
2) Run the following concurrently:
2-1) send() sk-B to sk-B from sk-X
2-2) close() both A and B
At 2-1), there is a small window where unix_add_edges()
publishes a new edge (B <-> B) to GC but its skb is not queued
by skb_queue_tail().
If 2-2) completes before skb_queue_tail() and GC is triggered,
it judges A <-> B as dead, but B is not freed because GC cannot
collect the not-yet-queued skb holding the B <-> B edge.
X -. A <-> B -. This edge is visible
^--' ^..' but skb is not
This itself is not a problem since the next GC run will judge
B as dead as well and free it finally.
X -. A <.> B -.
^--' ^--'
However, X's SCC forces the next GC to call unix_walk_scc_fast(),
and it iterates over A through B's scc_entry.
Let's unlink scc_entry before freeing the vertex in unix_del_edge(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: fib: Don't dump dying fib_info in fib_leaf_notify().
syzbot reported use-after-free in nsim_fib4_prepare_event(). [0]
The problem is that the following functions call fib_info_hold() /
refcount_inc() while dumping fib_info under RCU, which is unsafe.
* mlxsw_sp_router_fib4_event()
* rocker_router_fib_event()
* nsim_fib4_prepare_event()
refcount_inc_not_zero() must be used, but it would be too late
there.
Let's guarantee the lifetime of fib_info in fib_leaf_notify().
Note that IPv6 does not need the corresponding change since
fib6_table_dump() holds fib6_table.tb6_lock.
[0]:
refcount_t: addition on 0; use-after-free.
WARNING: lib/refcount.c:25 at refcount_warn_saturate+0x9f/0x110 lib/refcount.c:25, CPU#0: kworker/u8:15/3420
Modules linked in:
CPU: 0 UID: 0 PID: 3420 Comm: kworker/u8:15 Not tainted syzkaller #0 PREEMPT_{RT,(full)}
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
Workqueue: netns cleanup_net
RIP: 0010:refcount_warn_saturate+0x9f/0x110 lib/refcount.c:25
Code: eb 66 85 db 74 3e 83 fb 01 75 4c e8 1b f1 22 fd 48 8d 3d 84 cb f1 0a 67 48 0f b9 3a eb 4a e8 08 f1 22 fd 48 8d 3d 81 cb f1 0a <67> 48 0f b9 3a eb 37 e8 f5 f0 22 fd 48 8d 3d 7e cb f1 0a 67 48 0f
RSP: 0018:ffffc9000f2c7270 EFLAGS: 00010293
RAX: ffffffff84a18858 RBX: 0000000000000002 RCX: ffff888032ff9ec0
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff8f9353e0
RBP: 0000000000000000 R08: ffff888032ff9ec0 R09: 0000000000000005
R10: 0000000000000100 R11: 0000000000000004 R12: ffff8880570cc000
R13: dffffc0000000000 R14: ffff88802b40563c R15: ffff8880570cc000
FS: 0000000000000000(0000) GS:ffff888126173000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb1f4d5d000 CR3: 000000006072a000 CR4: 00000000003526f0
Call Trace:
<TASK>
__refcount_add include/linux/refcount.h:-1 [inline]
__refcount_inc include/linux/refcount.h:366 [inline]
refcount_inc include/linux/refcount.h:383 [inline]
fib_info_hold include/net/ip_fib.h:629 [inline]
nsim_fib4_prepare_event drivers/net/netdevsim/fib.c:930 [inline]
nsim_fib_event_schedule_work drivers/net/netdevsim/fib.c:1000 [inline]
nsim_fib_event_nb+0x1055/0x1240 drivers/net/netdevsim/fib.c:1043
call_fib_notifier+0x45/0x80 net/core/fib_notifier.c:25
call_fib_entry_notifier net/ipv4/fib_trie.c:90 [inline]
fib_leaf_notify net/ipv4/fib_trie.c:2176 [inline]
fib_table_notify net/ipv4/fib_trie.c:2194 [inline]
fib_notify+0x36b/0x5e0 net/ipv4/fib_trie.c:2217
fib_net_dump net/core/fib_notifier.c:70 [inline]
register_fib_notifier+0x184/0x360 net/core/fib_notifier.c:108
nsim_fib_create+0x85d/0x9f0 drivers/net/netdevsim/fib.c:1596
nsim_dev_reload_create drivers/net/netdevsim/dev.c:1604 [inline]
nsim_dev_reload_up+0x374/0x7c0 drivers/net/netdevsim/dev.c:1058
devlink_reload+0x501/0x8d0 net/devlink/dev.c:475
devlink_pernet_pre_exit+0x1ff/0x420 net/devlink/core.c:558
ops_pre_exit_list net/core/net_namespace.c:161 [inline]
ops_undo_list+0x187/0x940 net/core/net_namespace.c:234
cleanup_net+0x56e/0x800 net/core/net_namespace.c:702
process_one_work kernel/workqueue.c:3314 [inline]
process_scheduled_works+0xb5d/0x1860 kernel/workqueue.c:3397
worker_thread+0xa53/0xfc0 kernel/workqueue.c:3478
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Guard __get_user acesss with access_ok for uprobe_multi data
As reported by sashiko [1] we need to use access_ok to check the user
space data bounds before we use __get-user to get it.
[1] https://lore.kernel.org/bpf/20260610145235.CB1441F00893@smtp.kernel.org/ |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: platform: defer connection counter increment until alloc succeeds
coresight_add_out_conn() increments nr_outconns before calling
devm_krealloc_array() and again before devm_kmalloc(). If either
allocation fails, the counter is already bumped while the corresponding
array entry is NULL or uninitialized garbage.
coresight_add_in_conn() has the same problem with nr_inconns and
devm_krealloc_array().
In both cases the probe returns -ENOMEM, which causes
coresight_get_platform_data() to call coresight_release_platform_data()
for cleanup. That function iterates up to nr_outconns (or nr_inconns)
entries and dereferences each pointer unconditionally, hitting the NULL
or garbage entry and panicking instead of failing gracefully.
Fix by moving the counter increments to after all allocations succeed,
so the struct is always consistent on any error path. |
