| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: sideband: fix ring sg table pages leak
xhci_ring_to_sgtable() allocates a temporary pages array and
uses it to build the returned sg_table with
sg_alloc_table_from_pages().
The error paths free the pages array, but the success path
returns the sg_table without freeing it. This leaks the temporary
array every time a sideband client gets an endpoint or event ring
buffer.
Free the pages array after sg_alloc_table_from_pages() succeeds.
The returned sg_table has its own scatterlist entries and does not
depend on the temporary array after construction. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: cmipci: check snd_ctl_new1() return value
snd_ctl_new1() can return NULL when memory allocation fails.
snd_cmipci_spdif_controls() does not check the return value before
dereferencing kctl->id.device, which can lead to a NULL pointer
dereference.
Add NULL checks after snd_ctl_new1() calls and return -ENOMEM if any
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: 6lowpan: only accept IPv6 packets in lowpan_xmit()
The aoe driver (or similar) generates a non-IPv6 packet
(e.g., ETH_P_AOE) and queues it for transmission via dev_queue_xmit()
on a 6LoWPAN interface (configured by the user or test case).
Since the packet is not IPv6, the 6LoWPAN header_ops->create function
(lowpan_header_create or header_create) returns early without initializing
the lowpan_addr_info structure in the skb headroom.
In the transmit function (lowpan_xmit), the driver calls lowpan_header
(or setup_header) which unconditionally copies and uses the lowpan_addr_info
from the headroom, which contains uninitialized data.
Fix this by dropping non IPv6 packets.
A similar fix is needed in net/bluetooth/6lowpan.c bt_xmit(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Bound iscsi_encode_text_output() appends to rsp_buf
iscsi_encode_text_output() concatenates "key=value\0" records into
login->rsp_buf, an 8192-byte kzalloc(MAX_KEY_VALUE_PAIRS) buffer
allocated in iscsit_alloc_login_setup_buffer(). The three sprintf() call
sites in this function (lines 1398, 1411, 1424 in v7.1-rc2) never check
the remaining buffer capacity:
*length += sprintf(output_buf, "%s=%s", er->key, er->value);
*length += 1;
output_buf = textbuf + *length;
The 8192-byte ceiling at iscsi_target_check_login_request() bounds the
*input* Login PDU payload, but a single PDU can carry up to 2048 minimal
four-byte "a=b\0" pairs, each unknown key expanding to a 16-byte
"a=NotUnderstood\0" output record via iscsi_add_notunderstood_response().
2048 * 16 = 32 KiB of output into an 8 KiB buffer, producing a ~24 KiB
heap overrun in the kmalloc-8k slab.
The fix introduces a static iscsi_encode_text_record() helper that uses
snprintf() with a per-call bounds check against the remaining buffer,
and threads a u32 textbuf_size parameter through
iscsi_encode_text_output(). Both call sites in
iscsi_target_handle_csg_zero() (PHASE_SECURITY) and
iscsi_target_handle_csg_one() (PHASE_OPERATIONAL) pass
MAX_KEY_VALUE_PAIRS. On overflow the encoder logs the condition, calls
iscsi_release_extra_responses() to drop queued records, and returns -1;
both caller sites now emit ISCSI_STATUS_CLS_INITIATOR_ERR /
ISCSI_LOGIN_STATUS_INIT_ERR via iscsit_tx_login_rsp() before returning,
so the initiator sees an explicit failed-login response rather than a
silent connection drop. (Prior to this patch only the PHASE_OPERATIONAL
caller did that; the PHASE_SECURITY caller is converted to the same
shape.) |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: mct_u232: fix missing interrupt-in transfer sanity check
Add the missing sanity check on the size of interrupt-in transfers to
avoid parsing stale or uninitialised slab data (and leaking it to user
space). |
| In the Linux kernel, the following vulnerability has been resolved:
dma-buf: fix UAF in dma_buf_fd() tracepoint
Once FD_ADD() returns, the fd is live in the file descriptor table
and a thread sharing that table can close() it before DMA_BUF_TRACE()
runs. The close drops the last reference, __fput() frees the dma_buf,
and the tracepoint then dereferences dmabuf to take dmabuf->name_lock
-- slab-use-after-free.
Split FD_ADD() back into get_unused_fd_flags() + fd_install() and
emit the tracepoint between them. While the fdtable slot is reserved
with a NULL file pointer, a racing close() returns -EBADF without
entering __fput(), so the dma_buf stays alive across the trace. Same
approach as commit 2d76319c4cbb ("dma-buf: fix UAF in dma_buf_put()
tracepoint").
This undoes the FD_ADD() conversion done in commit 34dfce523c90
("dma: convert dma_buf_fd() to FD_ADD()"); FD_ADD() has no place to
hook the tracepoint safely. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: Fix DMA fence leak in iio_buffer_enqueue_dmabuf()
iio_buffer_enqueue_dmabuf() allocates a struct iio_dma_fence (104 bytes,
kmalloc-128) via kmalloc_obj()+dma_fence_init(), which sets the initial
kref to 1. It then calls dma_resv_add_fence() which takes a second
reference (kref=2), and stores a raw pointer in block->fence.
On the success path the function returns without calling dma_fence_put()
to release the initial reference, so every buffer enqueue permanently
leaks one kmalloc-128 allocation.
The iio_buffer_cleanup() work item only releases the temporary reference
taken during completion signalling by iio_buffer_signal_dmabuf_done();
the initial reference from dma_fence_init() is never released.
With four iio_rwdev instances at 240kHz and 512 samples per buffer,
this produces ~1875 kmalloc-128 allocations per second matching the
observed slab growth exactly. A test with ftrace confirmed that the
dma_fence_destroy event was never triggered.
Fix by calling dma_fence_put() after dma_resv_add_fence(), transferring
ownership of the fence to the DMA reservation object. The DMA fence then
gets properly discarded after being signalled. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: itg3200: fix i2c read into the wrong stack location
itg3200_read_all_channels() takes `__be16 *buf' as a parameter and
fills the i2c_msg destination as `(char *)&buf'. Since `buf' is the
parameter (a pointer), `&buf' is the address of the local pointer
slot on the stack of itg3200_read_all_channels(), not the address
of the caller's scan buffer. The (char *) cast hides the type
mismatch.
i2c_transfer() therefore writes ITG3200_SCAN_ELEMENTS * sizeof(s16)
= 8 bytes into the parameter's stack slot, which is discarded when
the function returns. The caller's scan buffer in
itg3200_trigger_handler() is never written to, so
iio_push_to_buffers_with_timestamp() pushes uninitialised stack
contents to userspace via /dev/iio:deviceX every scan -- both a
functional bug (no actual gyroscope or temperature data is
delivered through the triggered buffer) and an information leak.
The non-buffered read_raw() path is unaffected: it goes through
itg3200_read_reg_s16() which uses `&out' on a local s16 value,
where that is correct.
Drop the spurious `&' so the i2c read writes into the caller's
buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skmsg: preserve sg.copy across SG transforms
The sk_msg sg.copy bitmap is part of the scatterlist entry ownership
state. A set bit tells sk_msg_compute_data_pointers() not to expose the
entry through writable BPF ctx->data. This protects entries backed by
pages that are not private to the sk_msg, such as splice-backed file
page-cache pages.
Several sk_msg transform paths move, copy, split, or compact
msg->sg.data[] entries without moving the matching sg.copy bit. This can
make an externally backed entry arrive at a new slot with a clear copy
bit. A later SK_MSG verdict can then expose sg_virt(sge) as writable
ctx->data and BPF stores can modify the original page cache.
Keep sg.copy synchronized with sg.data[] whenever entries are
transferred, shifted, split, or copied into a new sk_msg. Clear the bit
when an entry is replaced by a newly allocated private page or freed.
This covers the BPF pull/push/pop helpers, sk_msg_shift_left/right(),
sk_msg_xfer(), and tls_split_open_record(), including the partial tail
entry created during TLS open-record splitting. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip_gre: require CAP_NET_ADMIN in the device netns for changelink
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the tunnel link netns t->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Add rtnl_dev_link_net_capable() next to rtnl_get_net_ns_capable() in
net/core/rtnetlink.c. It requires CAP_NET_ADMIN in the link netns and is
skipped when the link netns is dev_net(dev), where the rtnl path already
checked it. The other patches in this series use the same helper.
Gate ipgre_changelink() and erspan_changelink() with it, at the top of
the op before any attribute is parsed, because the parsers update live
tunnel fields first. ipgre_netlink_parms() sets t->collect_md before
ip_tunnel_changelink() runs.
Commit 8b484efd5cb4 ("ip6: vti: Use ip6_tnl.net in
vti6_siocdevprivate().") added the same check on the ioctl path. This
adds it on RTM_NEWLINK. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: mediate the implicit connect of TCP fast open sendmsg
sendmsg()/sendto() with MSG_FASTOPEN is a combination of connect(2) and
write(2): it opens the connection in the SYN. apparmor_socket_sendmsg()
only checks AA_MAY_SEND, so a profile that grants send but denies connect
lets a confined task open an outbound TCP/MPTCP connection that connect(2)
would have refused, bypassing connect mediation.
Mediate the implicit connect when MSG_FASTOPEN is set and a destination
is supplied. Add it to apparmor_socket_sendmsg() (not the shared
aa_sock_msg_perm() helper, which recvmsg also uses) and call aa_sk_perm()
directly, mirroring the selinux and tomoyo fixes. sk_is_tcp() does not
cover MPTCP fast open, so the SOCK_STREAM/IPPROTO_MPTCP arm is explicit. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: fix use-after-free in rawdata dedup loop
aa_replace_profiles() walks ns->rawdata_list to dedup the incoming
policy blob against entries already attached to existing profiles.
Per the kernel-doc on struct aa_loaddata, list membership does not
hold a reference: profiles hold pcount, and when the last pcount
drops, do_ploaddata_rmfs() is queued on a workqueue that takes
ns->lock and removes the entry. Between dropping the last pcount
and the workqueue running, an entry remains on the list with
pcount == 0.
aa_get_profile_loaddata() is an unconditional kref_get() on
pcount, so when the dedup loop hits such an entry, refcount
hardening reports
refcount_t: addition on 0; use-after-free.
inside aa_replace_profiles(), and the poisoned counter then
trips "saturated" and "underflow" warnings on the subsequent
uses of the same loaddata.
Before commit a0b7091c4de4 ("apparmor: fix race on rawdata
dereference") the dedup path used a get_unless_zero-style helper
on a single counter, so the existing "if (tmp)" guard was
meaningful. The split-refcount refactor introduced
aa_get_profile_loaddata(), which has plain kref_get() semantics,
and the guard quietly became a no-op.
Introduce aa_get_profile_loaddata_not0(), matching the existing
_not0 convention used by aa_get_profile_not0(), and use it for
the rawdata_list dedup lookup so dying entries are skipped.
Reproduced on x86_64 with v7.1-rc5 in QEMU+KVM running Ubuntu
24.04 + stress-ng 0.17.06:
stress-ng --apparmor 1 --klog-check --timeout 60s
Without this patch the three refcount_t warnings fire within a
few seconds. With it the same 60 s run is clean. Coverage is a
smoke-test only; a longer soak with CONFIG_KASAN, CONFIG_KCSAN
and CONFIG_PROVE_LOCKING would be welcome from anyone with the
cycles. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: validate orphan inode entry count
f2fs_recover_orphan_inodes() trusts the orphan block entry_count when
replaying orphan inodes from the checkpoint pack. A corrupted entry_count
larger than F2FS_ORPHANS_PER_BLOCK makes the recovery loop read past the
ino[] array and interpret footer or following data as inode numbers.
On a crafted image, mounting an unpatched kernel can drive orphan recovery
into f2fs_bug_on() and panic the kernel. Validate entry_count before
consuming entries so corrupted checkpoint data fails the mount with
-EFSCORRUPTED and requests fsck instead.
Set ERROR_INCONSISTENT_ORPHAN as well, so the corruption reason can be
recorded in the superblock s_errors[] field. This gives fsck a persistent
hint even though mount-time orphan recovery failure may leave no chance to
persist SBI_NEED_FSCK through a checkpoint. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: validate compress cache inode only when enabled
F2FS_COMPRESS_INO() uses NM_I(sbi)->max_nid as the synthetic inode
number for the compressed page cache inode. That inode only exists when
the compress_cache mount option is enabled.
When compress_cache is disabled, max_nid is outside the valid inode
range. A corrupted directory entry that points to ino == max_nid should
therefore be rejected by f2fs_check_nid_range(). However, is_meta_ino()
currently treats F2FS_COMPRESS_INO() as a meta inode unconditionally,
so f2fs_iget() bypasses do_read_inode() and its nid range check, and
instantiates a fake internal inode instead.
Gate the compressed cache inode case on COMPRESS_CACHE, matching
f2fs_init_compress_inode(). With compress_cache disabled, ino ==
max_nid now follows the normal inode path and is rejected as an
out-of-range nid. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: atomic: fix UAF issue on f2fs_inode_info.atomic_inode
- ioctl(F2FS_IOC_GARBAGE_COLLECT_RANGE) - shrink
- f2fs_gc
- gc_data_segment
- ra_data_block(cow_inode)
- mapping = F2FS_I(inode)->atomic_inode->i_mapping
: f2fs_is_cow_file(cow_inode) is true
- f2fs_evict_inode(atomic_inode)
- clear_inode_flag(fi->cow_inode, FI_COW_FILE)
- F2FS_I(fi->cow_inode)->atomic_inode = NULL
...
- truncate_inode_pages_final(atomic_inode)
- f2fs_grab_cache_folio(mapping)
: create folio in atomic_inode->mapping
- clear_inode(atomic_inode)
- BUG_ON(atomic_inode->i_data.nrpages)
We need to add a reference on fi->atomic_inode before using its mapping
field during garbage collection, otherwise, it will cause UAF issue. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: bound i_inline_xattr_size for non-inline-xattr inodes
When the flexible_inline_xattr feature is enabled, do_read_inode() loads
the on-disk i_inline_xattr_size unconditionally:
if (f2fs_sb_has_flexible_inline_xattr(sbi))
fi->i_inline_xattr_size = le16_to_cpu(ri->i_inline_xattr_size);
but sanity_check_inode() only range-checks it when the inode also has the
FI_INLINE_XATTR flag set. An inode that carries an inline dentry or inline
data but not FI_INLINE_XATTR -- the normal layout for an inline
directory -- therefore keeps a fully attacker-controlled
i_inline_xattr_size from a crafted image.
get_inline_xattr_addrs() returns that value with no flag gating, so it
feeds the inode geometry:
MAX_INLINE_DATA() = 4 * (CUR_ADDRS_PER_INODE - i_inline_xattr_size - 1)
NR_INLINE_DENTRY() = MAX_INLINE_DATA() * BITS_PER_BYTE / (...)
addrs_per_page() = CUR_ADDRS_PER_INODE - i_inline_xattr_size
A large i_inline_xattr_size drives MAX_INLINE_DATA() and NR_INLINE_DENTRY()
negative, so make_dentry_ptr_inline() sets d->max (int) to a negative
value. The inline directory walk then compares an unsigned long bit_pos
against that negative d->max, which is promoted to a huge unsigned bound,
and reads far past the inline area:
while (bit_pos < d->max) /* fs/f2fs/dir.c */
... test_bit_le(bit_pos, d->bitmap) / d->dentry[bit_pos] ...
Mounting a crafted image and reading such a directory triggers an
out-of-bounds read in f2fs_fill_dentries(); the same underflow also
corrupts ADDRS_PER_INODE for regular files.
Validate i_inline_xattr_size against MAX_INLINE_XATTR_SIZE whenever the
flexible_inline_xattr feature is enabled -- i.e. whenever the value is
loaded from disk and consumed -- and keep the lower MIN_INLINE_XATTR_SIZE
bound gated on inodes that actually carry an inline xattr, so legitimate
inodes with i_inline_xattr_size == 0 are still accepted. |
| In the Linux kernel, the following vulnerability has been resolved:
hdlc_ppp: sync per-proto timers before freeing hdlc state
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
rpmsg: char: Fix use-after-free on probe error path
rpmsg_chrdev_probe() stores the newly allocated eptdev in the default
endpoint's priv pointer before calling rpmsg_chrdev_eptdev_add(). If
rpmsg_chrdev_eptdev_add() then fails, its error path frees eptdev while
the default endpoint may still dispatch callbacks with the stale priv
pointer.
Avoid publishing eptdev through the default endpoint until
rpmsg_chrdev_eptdev_add() succeeds. Messages received before the priv
pointer is published should be ignored by rpmsg_ept_cb(). Flow-control
updates can hit rpmsg_ept_flow_cb() in the same window, so make both
callbacks return success when priv is NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: release layout stid on setlease failure
nfs4_alloc_stid() publishes the new stid into cl->cl_stateids via
idr_alloc_cyclic() under cl_lock before returning to
nfsd4_alloc_layout_stateid(). When nfsd4_layout_setlease() then
fails, the error path frees the layout stateid directly with
kmem_cache_free() without ever calling idr_remove(), leaving the
IDR slot pointing at freed slab memory. Any subsequent IDR walker
(states_show, client teardown) dereferences the dangling pointer.
The correct teardown for an IDR-published stid is nfs4_put_stid(),
which removes the IDR slot under cl_lock, dispatches sc_free
(nfsd4_free_layout_stateid) to release ls->ls_file via
nfsd4_close_layout(), and drops the nfs4_file reference in its
tail.
A second issue blocks that switch: nfsd4_free_layout_stateid()
unconditionally inspects ls->ls_fence_work via
delayed_work_pending() under ls_lock, but
INIT_DELAYED_WORK(&ls->ls_fence_work, ...) currently runs only
after the setlease call. On the setlease-failure path the
destructor would touch an uninitialized delayed_work.
nfsd4_alloc_layout_stateid()
nfs4_alloc_stid() /* idr_alloc_cyclic under cl_lock */
nfsd4_layout_setlease() /* fails */
nfs4_put_stid()
nfsd4_free_layout_stateid()
delayed_work_pending(&ls->ls_fence_work) /* needs INIT */
nfsd4_close_layout() /* nfsd_file_put(ls->ls_file) */
put_nfs4_file()
Fix by hoisting the ls_fenced / ls_fence_delay / INIT_DELAYED_WORK
initialization above the nfsd4_layout_setlease() call, and replace
the manual nfsd_file_put + put_nfs4_file + kmem_cache_free cleanup
with a single nfs4_put_stid(stp). |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: reset write verifier on deferred writeback errors
nfsd_vfs_write() and nfsd_commit() both call filemap_check_wb_err() to
detect deferred writeback errors, but neither rotates the server's write
verifier (nn->writeverf) when this check fails. Every other
durable-storage-failure path in these functions calls
commit_reset_write_verifier() before returning an error.
The missing rotation means clients holding UNSTABLE write data under the
current verifier will COMMIT, receive the unchanged verifier back, and
conclude their data is durable — silently dropping data that failed
writeback. This violates the UNSTABLE+COMMIT durability contract
(RFC 1813 §3.3.7, RFC 8881 §18.32).
Add commit_reset_write_verifier() calls at both filemap_check_wb_err()
error sites, matching the pattern used by adjacent error paths in the
same functions. The helper already filters -EAGAIN and -ESTALE
internally, so the calls are unconditionally safe. |
