| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Use rollback index when freeing MSI-X vectors
pm8001_request_msix() unwinds previously registered handlers with
free_irq() when request_irq() fails. The rollback loop uses the failing
index i for every iteration instead of the already registered vector
index j.
That passes the wrong IRQ/dev_id pair to free_irq() and leaves the
earlier handlers installed. Use j for both pci_irq_vector() and the
matching irq_vector entry in the rollback loop. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: megaraid_sas: Limit NVMe request size to the PRP chain frame
megasas_make_prp_nvme() builds a command's PRP list in cmd->sg_frame, a
DMA pool buffer of instance->max_chain_frame_sz bytes, spending one
entry per NVMe page of the transfer plus one per page of the buffer for
the chain pointer. The loop runs until the transfer is described and
never checks the buffer bound.
max_hw_sectors comes straight from the MDTS the firmware reports for the
drive. On drives with a large MDTS the only thing keeping the list
inside the buffer was the block layer default of 1280 KiB, which needs
320 entries, which fit into a 4 KiB frame as that holds 512. But since
commit 9b8b84879d4a ("block: Increase BLK_DEF_MAX_SECTORS_CAP") that
default is 4 MiB, and such a transfer needs 1025 entries, so the list
runs a full page past the end of the frame:
sd 1:0:1:0: [sdb] tag#630 page boundary ptr_sgl: 0x00000000ba62d13f
BUG: unable to handle page fault for address: ff663bcb81e7c000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:megasas_build_and_issue_cmd_fusion+0xeaa/0x1870 [megaraid_sas]
If the page after the frame happens to be mapped, the overrun does not
fault but silently corrupts the neighbouring pool entry, which is
another in-flight command's PRP list.
Cap max_hw_sectors at what the chain frame can describe, less one page
for transfers that do not start on a page boundary and so need one entry
more. This is the megaraid_sas counterpart of commit 04631f55afc5
("scsi: mpt3sas: Limit NVMe request size to 2 MiB"), but derives the
limit from max_chain_frame_sz rather than hardcoding it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: bsg: Cap io_uring sense copy to max_response_len
Completion copied scmd->sense_len to the user response buffer without
honoring max_response_len. After a valid sense, the midlayer sets
sense_len to the real length (up to SCSI_SENSE_BUFFERSIZE), so a smaller
user buffer was overrun. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_action_frame_parse()
rtw_action_frame_parse() takes a frame_len parameter but never
actually checks it before indexing into the frame body:
const u8 *frame_body = frame + sizeof(struct ieee80211_hdr_3addr);
...
c = frame_body[0];
...
a = frame_body[1];
frame_body already points 24 bytes (sizeof(struct
ieee80211_hdr_3addr)) into frame, so reading frame_body[0] and
frame_body[1] requires frame_len >= 26. A management action frame
shorter than that (e.g. exactly 24 bytes, the minimum a malicious
peer can send) causes a 1-2 byte out-of-bounds read.
This is reachable from rtw_cfg80211_monitor_if_xmit_entry() and
cfg80211_rtw_mgmt_tx() in ioctl_cfg80211.c, both of which pass
attacker/user-influenced frame buffers and lengths straight through.
Add the missing length check before frame_body is dereferenced. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read / stack overflow in rtw_get_wps_attr()
rtw_get_wps_attr() walks WPS attributes inside a WPS IE taken from
a wireless management frame. For each candidate attribute it only
checks that the fixed 4-byte attribute header (2-byte ID + 2-byte
length) fits inside the IE:
if (attr_ptr + 4 > wps_ie + wps_ielen)
break;
u16 attr_id = get_unaligned_be16(attr_ptr);
u16 attr_data_len = get_unaligned_be16(attr_ptr + 2);
u16 attr_len = attr_data_len + 4;
attr_data_len (and therefore attr_len) is read directly from the
wire and is never checked against the remaining bytes in the IE
before being used as the size of:
memcpy(buf_attr, attr_ptr, attr_len);
Since attr_len is fully attacker controlled (0 to 65535+4), this is
both a heap OOB read of wps_ie, and, more seriously, a stack buffer
overflow at several call sites where buf_attr is a single-byte
stack variable, e.g. rtw_get_wps_attr_content()'s callers passing
WPS_ATTR_SELECTED_REGISTRAR into a stack "u8 sr"/"u8
selected_registrar" (drivers/staging/rtl8723bs/os_dep/ioctl_cfg80211.c,
drivers/staging/rtl8723bs/core/rtw_mlme_ext.c). A crafted WPS IE in a
beacon or probe response processed during scanning can therefore
smash the stack of the parsing thread.
rtw_get_wps_attr_content() itself has no independent length check
and simply trusts the attr_len it gets back from rtw_get_wps_attr(),
so fixing the bound here also fixes that caller.
The "attr_ptr + 4 > wps_ie + wps_ielen" header check above was added
by commit 1463ca3ec6601 ("staging: rtl8723bs: fix OOB reads in
rtw_get_sec_ie(), rtw_get_wapi_ie(), and rtw_get_wps_attr()"), which
bounded the fixed header but never extended the check to cover the
variable-length attribute data that follows it. Add that missing
check before attr_len is used as a memcpy() length or accepted as a
match. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi2: fix use-after-free in string attribute show path
f_midi2_opts_str_show() takes the string lock internally, but its
callers dereference the opts->info.<field> pointer before calling it,
outside the lock. This races with f_midi2_opts_str_store(), which
frees the old string under opts->lock when the attribute is written
concurrently, the show path can read a pointer that gets freed
before the lock inside str_show() is even taken.
Change f_midi2_opts_str_show() to take a pointer to the string field,
matching the existing pattern in f_midi2_opts_str_store(), and
dereference it only after the lock is held. Update all three callers
(iface_name, block name, and the EP string option macro) accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_mass_storage: fix null pointer dereference in fsg_common_set_num_buffers()
Previously fsg_num_buffers_validate() was removed as it was not
necessary due to Kconfig setting the limits for n from 2 to 256 with
default as 2. However, setting the page content in such a way that
kstrtou8() reflects n value as either 0 or 1 bypasses these
restrictions leading to a null pointer dereference if n is 0. Fix
this by adding a check for n < 2 and returning -EINVAL if n is
either 0 or 1 consistent with Kconfig logic. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic: cancel reset_work on stop
pdphy_stop() disables IRQs but leaves reset_work pending. If the IRQ
handler schedules it just before disable_irq(), the work runs after
remove() frees the struct via devm.
Call cancel_work_sync() after disabling IRQs to close the window.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
usb-storage: ene_ub6250: fix race between scan work and probe
ene_ub6250_probe() calls usb_stor_probe2(), which starts the usb-storage
infrastructure and schedules the delayed scan work. The driver then
calls ene_get_card_type(), which sends an ENE command through
ene_send_scsi_cmd() and the usb-storage bulk transfer helpers.
Both the delayed scan work, through usb_stor_Bulk_max_lun(), and
ene_get_card_type() use us->current_urb. The scan work serializes this
access with us->dev_mutex, but the ENE card-type probe does not. If the
scan work runs while ene_get_card_type() is still using us->current_urb,
usb_submit_urb() warns that the URB is already active.
Serialize ene_get_card_type() with us->dev_mutex, matching the locking
used by the scan path. |
| In the Linux kernel, the following vulnerability has been resolved:
media: usbtv: keep device alive while ALSA card exists
The ALSA PCM callbacks store the driver state in pcm->private_data. An
open PCM file can outlive USB disconnect because usbtv_audio_free() uses
snd_card_free_when_closed(). The disconnect path can then drop the V4L2
device reference and free struct usbtv before ALSA releases the substream,
so a later close dereferences freed memory in snd_usbtv_pcm_close().
Take a V4L2 device reference for the ALSA card and drop it from the card
private_free callback. This keeps struct usbtv valid until ALSA has closed
the remaining files and freed the card. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: fix OOB write in snd_usbmidi_us122l_output()
The snd_usbmidi_us122l_output() picks a count of 2 on anything slower
than high speed and never relates it to ep->max_transfer. The URB
buffer holds exactly max_transfer bytes, so a device declaring a one
byte bulk endpoint takes two bytes from snd_rawmidi_transmit(), and the
memset that pads the rest computes 1 - 2 in int and wraps to SIZE_MAX.
Only 0x800e and 0x800f are pinned to nine bytes. The US-122MKII at
0x0644:0x8021 falls to the default and takes usb_maxpacket(), which the
USB core only clamps downward.
The akai and novation output ops in this file were given the same guard
recently. Do the same here. |
| In the Linux kernel, the following vulnerability has been resolved:
zram: fix slot lock bit position on big-endian 64-bit
The slot lock is a bit operation on the whole __lock word, which flags and
ac_time alias as two u32s. On little-endian the lock bit lands in the
position ZRAM_ENTRY_LOCK reserves in flags, so the aliasing works out. On
64-bit big-endian it lands in ac_time instead: with
ZRAM_TRACK_ENTRY_ACTIME enabled, storing the access time from
mark_slot_accessed() or slot_free() wipes out the held lock bit, letting
another CPU take the same slot lock; an access time value with that bit
set makes the slot look locked forever.
Shift the lock bit into the flags half of the word on big-endian 64-bit. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/page_alloc: don't spin_trylock() in NMI on UP
Patch series "mm/page_alloc: fixes for free_pages_nolock() on RT/UP".
Pre-existing bugs found by Sashiko during review of this other series:
https://lore.kernel.org/all/20260703-alloc-trylock-v5-0-c87b714e19d3@google.com/
I have not reproduced these bugs, and I suspect there is no real-world
user that is affected by them.
This patch (of 2):
As noted in can_spin_trylock(), using this is unsafe in this context.
commit 620b46ed6ae17 ("mm/page_alloc: return NULL early from
alloc_frozen_pages_nolock() in NMI on UP") fixed this on the alloc side
but missed the free side.
Impact: If BPF programs using these features in NMI (probably tracing) are
present on non-SMP builds this might crash the kernel and is probably
exploitable by local attackers for privilege escalation. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Don't hand out the flat CCS storage as usable VRAM
get_flat_ccs_offset() reads the base of the flat CCS storage from the
hardware, scales it by the number of enabled L3 nodes, and rounds the
result up to 128K. Everything below that offset is then handed to the
VRAM allocator as usable memory.
Rounding a limit that means "usable memory ends here" upwards publishes
whatever lies between the real base and the rounded one as free memory,
and that memory belongs to the compression hardware. The scaled value
has no reason to be 128K aligned, and on a Battlemage G21 with 16 GiB it
is not:
flat CCS base: raw 0x3fafff800, rounded 0x3fb000000
so the last 2 KiB of page 0x3fafff000 is CCS storage, in the allocator's
pool. Whatever is allocated there gets that tail overwritten by the
compression hardware, which needs no page-table entry, no buffer object
and no GPU submission to do it, and does it before userspace exists.
On this machine a Mesa VM's level-3 page table landed on that page on
every cold boot. It lost the entry covering the compositor's
batch-buffer heap, so the compositor's first submission faulted fetching
its batch and gdm restarted it forever: a black screen on an otherwise
working machine. Restarting gdm cleared it because the next VM's page
tables were allocated somewhere else.
Round down instead, to the page size the allocator works in. On this
machine that excludes exactly one page.
Reading the reserved page afterwards shows what had been writing it:
[369] 0xcccc000000000000
[371] 0xcc77000000000000
[373] 0xcccc000000000000
[375] 0xcc77000000000000
compression metadata, two bytes per sixteen, sitting where the driver
used to hand out memory.
The assertion that should have caught this compares the offset against
GSMBASE - ccs_size for equality. That value is 128K aligned, so it
agrees with the rounded-up offset precisely when the base is not
aligned - the check cannot fail in the case it exists to catch, and is
compiled out unless CONFIG_DRM_XE_DEBUG is set. Replace it with one
that can fail: CCS storage must not run into GSM.
[ And this was a debug session from hell, enormously helped by an AI
doing much of the grunt-work.
I'd like to call it my tireless helper, but the AI several times
stated flat out that this was impossible and unsolvable and that we
should just write a report about it.
I suspect those things have been trained by people who may not be
quite as stubborn as I am.
But while the AI was ready to give up several times, it did keep
adding debug code and analyzing it faithfully when I pushed. So credit
where credit is due and I let the AI write the commit message above.
This is basically a one-liner fixing a bogus "round_up()" to a
"round_down()", but there were 24 patches adding more and more debug
information to this, and 18 kernel boot to finally narrow it down to
this. - Linus ] |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: dw-edma: Initialize IRQ data before requesting IRQs
dw_edma_irq_request() passes struct dw_edma_irq to request_irq() before
dw_edma_channel_setup() fills the back pointer. A shared interrupt can
therefore enter the handler with dw_irq->dw still NULL, leading to a
NULL pointer dereference.
Set the back pointer before installing each handler. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-direct: return struct page from dma_direct_alloc_from_pool()
Commit 5b138c534fda ("dma-direct: factor out a dma_direct_alloc_from_pool
helper") changed dma_direct_alloc_from_pool() to return the CPU address
from dma_alloc_from_pool(). That fits dma_direct_alloc(), but
dma_direct_alloc_pages() also uses the helper and expects a struct page *.
Fix this by making dma_direct_alloc_from_pool() return the struct page *
again, and pass the CPU address back through an out-parameter for the
dma_direct_alloc() caller. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: validate report length in wacom_intuos_pro2_bt_irq
wacom_intuos_pro2_bt_irq() receives the wire report length in `len`
but never consults it before parsing. After the report-id gate it
unconditionally calls wacom_intuos_pro2_bt_pen() and then, selected by
features.type, a fixed chain of sub-parsers, none of which receive
`len`:
wacom_intuos_pro2_bt_pen(wacom);
if (type == INTUOSP2_BT || type == INTUOSP2S_BT) {
wacom_intuos_pro2_bt_touch(wacom);
wacom_intuos_pro2_bt_pad(wacom);
wacom_intuos_pro2_bt_battery(wacom);
} else {
wacom_intuos_gen3_bt_pad(wacom);
wacom_intuos_gen3_bt_battery(wacom);
}
Each sub-parser dereferences wacom->data at fixed offsets. The furthest
byte touched on each branch is:
INTUOSP2_BT / INTUOSP2S_BT: wacom_intuos_pro2_bt_pad() reads data[285]
(the touchring byte), so the report must be at least 286 bytes;
INTUOSHT3_BT ("gen3"): wacom_intuos_gen3_bt_battery() reads data[45],
so the report must be at least 46 bytes.
features.type is selected from the VID/PID id_table entry and
wacom_setup_device_quirks() force-registers the pen/pad/touch inputs
for that type independent of the report descriptor, so a malicious or
malfunctioning paired/spoofed Bluetooth peripheral can advertise that
VID/PID and send an undersized report that still satisfies the
data[0] == 0x80/0x81 gate. The driver then reads past the received
report and forwards the bytes to userspace via evdev (MSC_SERIAL /
ABS_MISC / ABS_WHEEL on the pen and pad input nodes), an out-of-bounds
read with a concrete userspace read-back channel, and a true
out-of-bounds read on transports whose backing buffer is sized to the
(small) report descriptor rather than a fixed-size staging buffer.
This is the same class of bug commit 2f1763f62909 ("HID: wacom: fix
out-of-bounds read in wacom_intuos_bt_irq") already hardened in the
sibling wacom_intuos_bt_irq(), which guards each report id against its
minimum length before parsing.
Guard wacom_intuos_pro2_bt_irq() the same way: before parsing, reject
reports shorter than the furthest offset the selected branch actually
dereferences, warn, and bail out. Because the whole pen/touch/pad/
battery chain runs unconditionally per branch, a single up-front check
against the maximum offset (286 bytes for INTUOSP2_BT/INTUOSP2S_BT,
46 bytes for the gen3 branch) bounds every sub-parser. Returning 0 on
a short report also skips those calls for the same malformed report,
which is the safe, conservative behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: bpf: serialize device reference release in struct_ops destroy path
__hid_bpf_ops_destroy_device() and hid_bpf_unreg() can race on the
same registration reference, double-putting struct hid_device and
freeing it while hid_destroy_device() still uses it. Serialize the
remove/NULL decision under hdev->bpf.prog_list_lock so exactly one
path releases each registration reference: unreg re-checks ops->hdev
under the lock and returns without putting when the destroy path
already cleared it; all put_device() calls happen after the lock is
dropped, which is safe because a concurrent unreg then observes
ops->hdev == NULL under the lock.
Background: each successful attach (hid_bpf_ops_reg) acquires one
device reference (hid_get_device()). Two paths can release it:
- device destruction: hid_destroy_device() -> hid_bpf_destroy_device()
-> __hid_bpf_ops_destroy_device(), which walks hdev->bpf.prog_list
under rcu_read_lock() and drops one reference per attached program;
- BPF link release: bpf map delete (no BPF_F_LINK) synchronously calls
st_ops->unreg() -> hid_bpf_unreg(), which drops the reference for
its own registration.
The coordination handshake (e->hdev = NULL on the destroy side vs
"if (!hdev) return" on the unreg side) is a TOCTOU check: the two
paths run under different lock domains (rcu_read_lock vs
prog_list_lock), so a concurrent unreg can read ops->hdev as
non-NULL, block on prog_list_lock, and then proceed while the
destroy traversal executes - both paths then drop the same
reference. The refcount reaches zero legitimately (each decrement
is individually valid), so no refcount_t saturation fires: the
device is simply freed while the transport is still inside
hid_destroy_device(), and subsequent teardown touches freed memory.
The fix serializes the remove/NULL decision under prog_list_lock on
both sides and moves the destroy-side puts outside the lock. With
the lock held, plain reads/writes of ops->hdev are sufficient; no
READ_ONCE/WRITE_ONCE are added, keeping the patch minimal.
Unlocked-read safety: the unlocked read of ops->hdev at the top of
hid_bpf_unreg() cannot touch a freed device, because the unreg path
itself still holds this registration's reference (released only by
its own hid_put_device() after the lock is dropped), and a destroy
traversal that already cleared ops->hdev makes the lock-internal
re-check return early without any put. At most one of the two
paths releases each registration reference. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Have show_event_filters/triggers files take trace array ref
The newly added files show_event_filters and show_event_triggers that show
all filters or triggers that are set within the trace array do not take a
reference for the trace array it is showing. Without taking a reference,
the trace_array may be freed via "rmdir" while a task is reading one of
theses files. Those files iterate all the events within an instance
(trace_array) and nothing prevents that instance from being freed while
its data is being read. This causes a use-after-free crash.
Have the open of both those files take the trace_array reference via the
trace_array_get() that prevents the trace_array from being freed while the
files are opened. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: fix NULL pointer dereference in gadget_dev_ioctl()
gadget_dev_ioctl() reads dev->gadget before acquiring dev->lock, but
dev->state is checked after acquiring the lock. Therefore a concurrent
bind can change the device state between these operations, which can
leave ioctl with a stale NULL gadget pointer and causing a NULL pointer
dereference at gadget->ops->ioctl.
Read dev->gadget while holding dev->lock so that the gadget pointer
and device state are sampled consistently. |
